lmxopcua/docs/drivers/AbCip.md

AB CIP Driver

In-process native-protocol driver that exposes Allen-Bradley CIP / EtherNet-IP controllers as OPC UA nodes. It runs inside the OtOpcUa server's .NET 10 AnyCPU process and talks to the PLC through the libplctag.NET wrapper — no gateway, no sidecar. One driver instance can serve many devices; per-device routing is keyed on the canonical ab://gateway[:port]/cip-path host-address string.

Supported families: ControlLogix, CompactLogix, Micro800, and GuardLogix. CIP has no native push model, so subscriptions are a polling overlay on top of IReadable.

For the driver spec (capability surface, config shape, type mapping), see docs/v2/driver-specs.md §3. For the manual test client, see Driver.AbCip.Cli.md. For the integration fixture coverage map, see AbServer-Test-Fixture.md.

Project Layout

Project	Role
src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.AbCip/	The driver — AbCipDriver, the libplctag runtime/enumerator/template-reader wrappers, the UDT read planner + template decoders, the host-address parser, and the ALMD alarm projection.
src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.AbCip.Contracts/	AbCipDriverOptions, AbCipDeviceOptions, AbCipTagDefinition / AbCipStructureMember, and the AbCipDataType / AbCipPlcFamily enums bound from the driver's DriverConfig JSON.

Per family the AbCipPlcFamilyProfile (PlcFamilies/AbCipPlcFamilyProfile.cs) supplies the libplctag plc attribute, default CIP path, ConnectionSize, and request-packing / connected-messaging quirks — ControlLogix is the baseline and each other family is a delta (Micro800 is unconnected-only with no backplane routing; GuardLogix shares the ControlLogix wire protocol with a tag-level safety partition).

Capability Surface

AbCipDriver : IDriver, IReadable, IWritable, ITagDiscovery, ISubscribable, IHostConnectivityProbe, IPerCallHostResolver, IAlarmSource, IDisposable, IAsyncDisposable (Driver.AbCip/AbCipDriver.cs). It adds IAlarmSource over the Modbus / AB Legacy surface.

Capability	Implementation entry point	Notes
ITagDiscovery	DiscoverAsync	Emits pre-declared tags under per-device folders; UDT tags with declared Members fan out into a sub-folder + one variable per member. With EnableControllerBrowse the @tags symbol table — plus each Program:<name>.@tags listing — is walked into a Discovered/ folder (system/module/routine tags filtered out).
IReadable	ReadAsync → ReadGroupAsync / ReadSingleAsync	Per-tag reads; opt-in whole-UDT grouping (EnableDeclarationOnlyUdtGrouping) collapses N member reads into one.
IWritable	WriteAsync	BOOL-within-DINT writes do a per-parent read-modify-write under a lock; SafetyTag and non-writable tags return BadNotWritable.
ISubscribable	SubscribeAsync driven by the shared PollGroupEngine	CIP has no push model — subscriptions become polling groups.
IHostConnectivityProbe	ProbeLoopAsync + GetHostStatuses	One probe loop per device reading Probe.ProbeTagPath; no path configured ⇒ a warning is logged and the device stays Unknown.
IPerCallHostResolver	ResolveHost	Routes each call to the tag's DeviceHostAddress, the breaker key for the resilience pipeline so one dead PLC trips only its own breaker.
IAlarmSource	AbCipAlarmProjection (ALMD)	Opt-in via EnableAlarmProjection; off by default the subscribe path is a no-op so capability negotiation still works.

Addressing Model

Per-device host addresses are the canonical ab://gateway[:port]/cip-path form parsed by AbCipHostAddress.TryParse (AbCipHostAddress.cs). The parsed CipPath is handed to libplctag verbatim, so no wire-layer translation is needed:

Form	Meaning
ab://10.0.0.5/1,0	Single-chassis ControlLogix, CPU in slot 0
ab://10.0.0.5/1,2,2,192.168.50.20,1,0	Bridged ControlLogix (routed path)
ab://10.0.0.5/	Micro800 / no-backplane device (empty path)
ab://10.0.0.5:44818/1,0	Explicit EIP port (default 44818)

Tags carry a Logix symbolic TagPath (controller or program scope). UDT-typed tags are declared as AbCipDataType.Structure with a Members list; discovery fans each member out as {tag.Name}.{member.Name}, and the read planner can collapse a batch of members into one whole-UDT read when EnableDeclarationOnlyUdtGrouping is set. The whole-UDT fast path is opt-in because Studio 5000 may reorder members vs declaration order; decoding at declaration-order offsets against a reordered layout yields silently-plausible wrong numbers.

Configuration

AbCipDriverOptions (Driver.AbCip.Contracts/AbCipDriverOptions.cs) binds from the driver's DriverConfig JSON. Key fields:

• Devices — one AbCipDeviceOptions per PLC (HostAddress, PlcFamily, optional DeviceName, per-device AllowPacking / ConnectionSize overrides).
• Tags — pre-declared AbCipTagDefinition list; Members for UDT fan-out, SafetyTag for GuardLogix safety-partition tags.
• Probe — connectivity-probe Enabled / Interval / Timeout / ProbeTagPath.
• Transport — absent (default ⇒ Native), Native, or Libplctag (fallback); see Transport.
• Discovery — EnableControllerBrowse (@tags walk) and EnableDeclarationOnlyUdtGrouping (whole-UDT read fast path).
• Alarms — EnableAlarmProjection + AlarmPollInterval for the ALMD projection.

Full per-field descriptions live in AbCipDriverOptions.cs. The JSON skeleton is reproduced in docs/v2/driver-specs.md §3.

Transport (transport option)

The driver has two interchangeable wire transports, selected by one DriverConfig key:

Key	Values	Default	Serialization
transport	absent | Native | Libplctag	absent ⇒ Native	string, case-insensitive on read, written as "Libplctag" / "Native"; "use the default" is encoded by OMITTING the key

• Native (the default since Task 22) is a managed in-process EtherNet/IP + CIP client (Driver.Ab.Transport).
• Libplctag (fallback) drives the libplctag native library, as before.
• An absent key means "use the default". It is resolved in one place, AbCipTransportResolver, which the driver, the Test Connect probe and the CLI all go through. An explicit value always wins.
• A bad value fails like a bad PlcFamily; the Test Connect probe reports "Config JSON is invalid".
• A change takes effect when the driver instance is constructed: on every process start (so the upgrade restart moves no-key drivers to Native — see the release note) and when a deploy that changes DriverConfig does this (DriverHostActor respawns the child, #516). ReinitializeAsync alone keeps the transport it was constructed with.
• AdminUI: the Transport dropdown in the advanced section of the AbCip driver form ("Default (Native)" / "Native (managed)" / "libplctag (fallback)"). Default omits the key on save, so a defaulted driver stays defaulted; saving another field preserves an explicit value and preserves absence.
• The driver logs transport=<effective> (default|configured) at Information on every init, e.g. transport=Native (default), including reconnect re-inits. AbCip drivers now receive the host logger (they previously ran on a null logger, so none of their warnings reached the node log); expect previously invisible warnings, e.g. a probe enabled with no probe tag path.
• CLI: --transport default|native|libplctag (default default, which goes through the same resolver).
• libplctag is confined to Libplctag*.cs adapters, enforced by a source-scan guard (LibplctagConfinementGuardTests), so removing it later is mechanical.

Release note — native is the default (Task 22)

• The native managed transport is now the default. A driver config with no transport key runs Native; libplctag remains available as the fallback.
• ⚠️ Client-visible: native reports BadTypeMismatch for a mis-authored same-width type (for example a tag authored DINT where the controller holds a REAL), where libplctag returned Good garbage. Correct the authored type; see Native transport behaviour.
• To fall back, set "transport": "Libplctag" in the driver config (or pick "libplctag (fallback)" in the AdminUI dropdown).
• ⚠️ When it takes effect: the upgrade restart itself. Every process start constructs the drivers (including boot-from-cache on a driver-only node), so every driver with no transport key moves to Native the moment the upgraded node starts — no deploy is needed. To keep a driver on libplctag, add "transport": "Libplctag" and deploy it before upgrading: older builds ignore the unknown key. After the upgrade, a transport change takes effect when a deploy recreates the driver (not on ReinitializeAsync).
• Evidence, and its limits: AbCip reads (plus browse and templates) were proven on a production CompactLogix 5069-L320ERS2 (Z-35162, read-only, 2026-10-08; see gate results §Real press). AbCip writes are simulator-proven only (ab_server), as is all of AbLegacy.
• AbLegacy has its own exclusion: a defaulted AbLegacy driver with any PLC-5 or logixpccc device stays on libplctag (see AbLegacy.md §Transport).

Native transport behaviour

• One CIP connection and one request scheduler per device (DeviceSessionPool), shared by reads, writes, browse and template reads. The Multiple Service Packet scheduler coalesces requests with one request in flight; large reads (listing pages, Read Template) are sent unpacked and exclusive.
• Forward Open throttle: at most one attempt in flight, at least 1 s between starts, bounded by the open budget.
• ConnectionSize / Timeout are honoured per pooled connection, and the first driver/device to open a given device key wins. ControlLogix, GuardLogix and (since T21) CompactLogix default to 4002, a Large Forward Open (0x5B), the same as libplctag. A target that refuses Large gets one regular open at min(size, 504) inside the same throttled attempt. An explicit ConnectionSize in the options or on the device overrides the family default.
• Routing: Micro800 is connected with an empty route regardless of UseConnectedMessaging. SLC500/MicroLogix/PLC-5 over this driver are direct. logixpccc uses UnconnectedSend; its SLC framing is unverified.
• ⚠️ Type check (client-visible change). The native path compares the type code the controller returns with the authored DataType and reports BadTypeMismatch on disagreement. libplctag never checks it, so a same-width mis-authored tag read as Good garbage: authoring a tag as DINT while the controller holds a REAL returns the REAL's bits as an integer with a Good status under libplctag, and BadTypeMismatch natively. That is the fix working, but a consumer will see Bad quality on tags that previously looked healthy: correct the authored type. Same-width signed/unsigned pairs are exempt, and writes are gated on a mismatch too.
• Malformed tag names put the device into backoff, as under libplctag (#570). STRING capacity includes the alignment pad (84, not 82) (#570).
• Status-bit sub-element writes (e.g. T4:0.DN) are Unsupported natively (they would clobber the control word); nothing goes on the wire. Sub-element arrays are Unsupported natively.
• A refused operation is not a comms fault. Any operation a runtime refuses as Unsupported (in AbCip, e.g. a native write whose type cannot be determined) reaches the client as BadNotSupported, keeps the tag handle, and leaves driver health unchanged; only real transport failures evict and degrade.

Known gaps

• ⚠️ Native writes are verified against ab_server only (simulator-only), never a real controller. The real-press gate (Task 21) was read-only: it proved native reads, browse and templates on Z-35162 (2026-10-08) and nothing else. Results: native-ab-transport-gate-results.
• libplctag cannot be deleted until a bench controller allows write verification.
• Wide-struct fragmented writes (8-byte alignment) are unit-tested only, never proven on a controller (#567).
• Native browse: listing pages are unpaced, and template reads outside an enumeration open a connection per call (#572).
• Micro800, routed and logixpccc paths are covered by ab_server only. The Micro800 profile passes natively. The AbLegacy default excludes logixpccc (and PLC-5).
• Follow-up issues for this workstream: #564 to #577.
• Fixed along the way (pre-existing on master): ab://host:44818/ with an empty CIP path (Micro800, unrouted MicroLogix) failed on libplctag with ErrorBadData because the adapter sent Path=""; it now sends no path.

Alarm Projection

IAlarmSource is served by AbCipAlarmProjection, which polls each subscribed ALMD UDT's InFaulted + Severity members at AlarmPollInterval and fires OnAlarmEvent on raise/clear transitions. It is ALMD-only in this pass (ALMA analog alarms are a follow-up) and disabled by default — shops running FT Alarm & Events should keep it off and take alarms through the native route, since the projection semantics don't exactly mirror Rockwell FT A&E.

Testing

• Unit tests — tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.AbCip.Tests/ cover the driver, host-address parser, UDT planner, and alarm projection via fake tag runtimes.
• Integration tests — tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.AbCip.IntegrationTests/ run against the ab_server Docker fixture. See AbServer-Test-Fixture.md for the coverage map and the AB_SERVER_ENDPOINT wiring.
• Manual client — Driver.AbCip.Cli.md.

1-D array support

An AB CIP tag becomes a 1-D OPC UA array node when its TagConfig JSON carries "isArray": true and "arrayLength": N (N ≥ 1). The canonical rule: isArray: true + arrayLength >= 1 → array; isArray: false (any length) → scalar.

Read mechanism — the driver delegates to libplctag's native array read. The tag's TagPath is passed to libplctag as a [N]-subscripted symbol (or the tag is created with an element count of N so libplctag fetches the full block in one EIP/CIP request). Both atomic types (DINT[N], REAL[N], …) and UDT member arrays are supported.

Unit test coverage — tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.AbCip.Tests/ covers array reads via the fake tag runtime for atomic and UDT member cases. The ab_server integration fixture is down during normal dev (Docker host fixture currently offline).

Live-verify — integration-fixture-gated (requires ab_server Docker fixture on 10.100.0.35:44818).

Deferrals — array writes, multi-dimensional arrays, per-element historization. Safety-partition array tags (SafetyTag: true) are excluded (GuardLogix write constraints extend to array writes).

See Uns.md §Array tags for the cross-driver coverage matrix and the UI authoring flow.

Controller-discovered UDT member variables

When EnableControllerBrowse is set, the driver walks the controller's @tags symbol table and surfaces each UDT-typed tag's atomic member leaves as individually addressable OPC UA Variables — in addition to the UDT container tag itself.

What is discovered

• Top-level UDT members — the Template Object for each controller-browse UDT is fetched via its template instance ID; each atomic member (BOOL, SINT, INT, DINT, REAL, …) becomes a separate Variable node under the UDT's Discovered/ sub-folder, addressable by its member path (e.g. MyUdt.Temperature, MyUdt.Flags). Top-level atomic member discovery is functional in production.

• Nested struct members — shipped (commits 3d8ce4e8 / d203f31c). When a UDT member is itself a struct, the Template Object member block carries the nested UDT's template instance ID in the low 12 bits of the member info field (struct flag 0x8000 set). The driver captures this as AbCipUdtMember.NestedTemplateId and threads it into a second FetchUdtShapeAsync call (@udt/{id}) so the nested struct's atomic leaves are expanded into dot-joined addressable paths (e.g. Motor1.Status.Code, Motor1.Status.Running). Recursion is bounded by a depth cap of 8 levels; members at or beyond the cap are dropped rather than emitted. Nested struct leaves that resolve to no emittable atomic leaf produce no sub-folder (lazy materialisation).

  ab_server (the default Docker simulator) does not implement the CIP Template Object service (class 0x6C), so the fixture cannot exercise it; see tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.AbCip.IntegrationTests/Emulate/AbCipEmulateNestedUdtTests.cs for the skip-gated Emulate smoke (backlog #6).

• STRING tags and members — a controller reports every STRING (built-in, or a user string type such as STR0016) as a LEN DINT + DATA SINT[n] struct. Discovery recognises that shape and emits one String variable, top-level or nested, instead of a LEN/DATA folder.

• Hidden members are skipped — the ZZZZZZZZZZ… hosts Logix packs BOOL members into and __… AOI backing members are not browsed (a user name can never start with __).

• Arrays — the Symbol Object's dimension bits populate IsArray/ElementCount (multi-dim flattened). An array of a UDT is emitted as one variable, not fanned out (Tag.Member names no element); an array of STRING is a String array.

• Program scope — @tags lists each program (Program:Main) but none of its tags; the enumerator reads every Program:<name>.@tags listing too, so program-scoped tags appear as Program:<name>.<tag>. One unreadable program listing is skipped, not fatal.

Real-controller verification (2026-10-07)

Run read-only against production CompactLogix 5069-L320ERS2 rev 34.11 presses (and a second CompactLogix) from the Mac over VPN. Before the fixes above, every real @udt/<id> buffer decoded to null (the decoder assumed a layout no controller sends — the test builders shared the assumption, the #468 trap), program-scoped tags were absent, and arrays browsed as scalars. After them, one browse of a press took ~30 s and produced 23,412 variables covering all 80 tags the Ignition project reads on it, with matching types. The template and symbol layouts are pinned by bytes captured off those controllers: CipTemplateObjectWireCaptureTests, CipSymbolObjectRealControllerCaptureTests, AbCipProgramScopeEnumerationTests.

Bare-container reads

Reading the UDT container tag itself (without a member suffix) returns BadNotSupported — address the atomic member leaves instead.

Member writes

UDT member writes discovered via controller browse are deferred in this release. Pre-declared Members with Writable: true retain full read/write support as before.

Configuration

No new configuration keys are required. Set EnableControllerBrowse: true in the AbCipDriverOptions JSON to enable the @tags walk; UDT member expansion is automatic for all UDT-typed tags found in the walk.

Operational Notes

• Native heap is invisible to the GC. libplctag's native Tag heap does not show up in CLR allocation figures. Watch whole-process RSS, and use ReinitializeAsync (tears down + re-creates every device's libplctag handles) as the remediation for native-heap growth. (There is no per-driver footprint number to consult: IDriver.GetMemoryFootprint() was deleted as unconsumed in Gitea #525.)
• Handle eviction on failure — a non-zero libplctag status or a transport exception evicts the cached tag runtime so the next read/write re-creates a fresh handle, mirroring the probe loop's recreate-on-failure behaviour.
• Read statuses carry the libplctag cause — a tag the controller does not have reads BadNodeIdUnknown (not BadCommunicationError), and it does not open the device's connect-backoff window (the controller answered; before this, one typo throttled every sibling tag on the device). A genuine connection failure still opens it.
• Width check on scalar reads — libplctag never checks the CIP type the controller returns. A scalar atomic read whose buffer is not the authored type's width (e.g. a REAL authored as INT — the legacy Kepware export does exactly this for some press tags) reads BadTypeMismatch instead of Good garbage. Same-width mistakes (DINT vs REAL) are undetectable under libplctag; the Native transport reports them as BadTypeMismatch (see Native transport behaviour).
• Module-defined I/O tags — Local:1:I.Data, ABB_OmniCore:I.ConnectionFaulted and similar colon-bearing base names are valid tag paths (controller scope only).
• User string arrays — STR0016[N] and similar arrays stride by the actual element size (read buffer ÷ count); libplctag.NET 1.5.2 leaves ElementSize unset after a read.
• Declaration-only UDT grouping is a footgun unless verified — only enable EnableDeclarationOnlyUdtGrouping when every UDT's member declaration order has been hand-verified against the controller's compiled layout.