diff --git a/docs/drivers/FOCAS-Test-Fixture.md b/docs/drivers/FOCAS-Test-Fixture.md
index 4cda662c..7875aedc 100644
--- a/docs/drivers/FOCAS-Test-Fixture.md
+++ b/docs/drivers/FOCAS-Test-Fixture.md
@@ -61,16 +61,21 @@ binary PDUs against the documented command IDs. Covered assertions:
 
 - Session open / close (`cnc_allclibhndl3` + `cnc_freelibhndl`)
 - Parameter read-back after `mock_patch` seed → `cnc_rdparam`
-- Macro read-back after seed → `cnc_rdmacro` (scaled-decimal
-  translation verified)
+- Macro read-back after seed → `cnc_rdmacro` (8-byte ODBM shape:
+  9-digit mantissa, `dec_val` at offset 6; vacant / fractional-on-integer
+  macros read Bad)
 - PMC range read after seed → `pmc_rdpmcrng`
 - `IAlarmSource` raise + clear transitions after `mock_patch`
   alarm-list changes → `cnc_rdalmmsg2`
 - Fixed-tree bootstrap: identity / axes / spindle / program / timers /
   servo meters populate via `cnc_sysinfo`, `cnc_rdaxisname`,
   `cnc_rdspdlname`, `cnc_rddynamic2`, `cnc_exeprgname2`,
-  `cnc_rdblkcount`, `cnc_rdopmode`, `cnc_rdsvmeter`, `cnc_rdspload`,
-  `cnc_rdspmaxrpm`, `cnc_rdtimer`
+  `cnc_rdblkcount`, `cnc_rdopmode`, `cnc_rdsvmeter`, `cnc_rdspmeter`
+  (load + motor speed, 1/16384 of full scale), `cnc_rdtimer`; positions
+  scale from each `cnc_rddynamic2` block's own base/exponent (the mock
+  refuses the non-existent `cnc_getfigure` 0x00D3, as a real 31i-B does).
+  The vendored mock's local divergence from upstream is listed in
+  `Docker/focas-mock/VENDORED.md`.
 - Per-series profile selection via `mock_load_profile` — tests can
   pin one profile and assert series-gated capability suppression
 
diff --git a/docs/drivers/FOCAS.md b/docs/drivers/FOCAS.md
index caa1d29b..3df703f6 100644
--- a/docs/drivers/FOCAS.md
+++ b/docs/drivers/FOCAS.md
@@ -31,8 +31,10 @@ protocol using the documented command IDs. Writes return
 > 31i-B (`10.201.31.5`) 2026-06-25:** sysinfo, axis/spindle names, dynamic positions/feed/spindle,
 > program/mode, **macros**, **timers** (8-byte payload is little-endian {minute, msec}), **PMC range**
 > (request widened to the data-type byte width), **servo meters** (8-byte LOADELM stride + names from
-> the 0x0089 block; load *scaling* still to be confirmed at commissioning), and **alarms** all read
-> correctly. The driver `cnc_rddynamic2` poll is 1-based. **`cnc_rdparam` is unsupported on this
+> the 0x0089 block), and **alarms** all read correctly. Several *decode* errors that survived that
+> validation (because they decode without failing — just wrongly) were later corrected from the
+> sister ignitionoee driver's live work on the same family of controls; see
+> [Wire decode corrections (2026-10)](#wire-decode-corrections-2026-10). The driver `cnc_rddynamic2` poll is 1-based. **`cnc_rdparam` is unsupported on this
 > control** — every request-framing variant returns `EW_FUNC` (likely a wrong v3 command id; needs a
 > reference FWLIB trace). The Test-Connect probe now runs a real wire session (initiate + cnc_statinfo)
 > instead of a bare TCP check. Full finding, captured wire bytes, validation results, and analysis:
@@ -187,11 +189,14 @@ fixed-tree paths are discovered from the machine, not composed from parts.
 
 Two caveats worth knowing before you browse:
 
-- **A real CNC can report duplicate sibling names, and they are disambiguated
-  automatically** (#548). One observed Makino returns two axes both called `AA`;
-  every member of such a collision set gets a 1-based occurrence suffix in slot
-  order — the tree offers `Axes/AA_1/` and `Axes/AA_2/`, each reading its own
-  axis — while unique names stay bare (`Axes/Y/`). The bare name of a duplicate
+- **A CNC that reports duplicate sibling names is disambiguated automatically**
+  (#548): every member of a collision set gets a 1-based occurrence suffix in slot
+  order (`Axes/AA_1/`, `Axes/AA_2/`), each reading its own axis, while unique names
+  stay bare (`Axes/Y/`). ⚠️ The Makino that motivated #548 does **not** in fact
+  report duplicates — its axes are `AA6` and `AA7`, and the wire layer used to read
+  only 2 of each 4-byte name record. Since the name-record fix those axes publish as
+  `Axes/AA6/` and `Axes/AA7/`; tags committed against `Axes/AA_1/…` / `Axes/AA_2/…`
+  on such a machine must be re-browsed and re-committed. The bare name of a duplicate
   set deliberately does not resolve: a tag authored against `Axes/AA/…` on such
   a machine reads `BadNodeIdUnknown` rather than one arbitrary axis's data. The
   suffix counts occurrences of the *same* name, so adding an unrelated axis
@@ -212,8 +217,8 @@ What gets populated (all under `FOCAS/{deviceHostAddress}/`, addressed as
 | `Identity/` | `SeriesNumber`, `Version`, `MaxAxes`, `CncType`, `MtType`, `AxisCount` | `cnc_sysinfo` once at bootstrap |
 | `Axes/{name}/` | `AbsolutePosition`, `MachinePosition`, `RelativePosition`, `DistanceToGo`, `ServoLoad` — one folder per discovered axis | `cnc_rdaxisname` once + `cnc_rddynamic2` + `cnc_rdsvmeter` per tick |
 | `Axes/FeedRate/Actual`, `Axes/SpindleSpeed/Actual` | Current feed + spindle RPM | `cnc_rddynamic2` |
-| `Spindle/{name}/` | `Load` (percentage), `MaxRpm` — one folder per discovered spindle | `cnc_rdspdlname` once + `cnc_rdspload` + `cnc_rdspmaxrpm` |
-| `Program/` | `Name` (filename), `ONumber`, `Number`, `MainNumber`, `Sequence`, `BlockCount` | `cnc_exeprgname2` + `cnc_rdblkcount` + cached `cnc_rddynamic2` |
+| `Spindle/{name}/` | `Load` (Float64, % of rated load), `MotorSpeedPct` (Float64, % of maximum speed) — one folder per discovered spindle | `cnc_rdspdlname` once + `cnc_rdspmeter` type 0 + type 1 per tick |
+| `Program/` | `Name` (filename), `ONumber`, `Number`, `MainNumber`, `Sequence`, `BlockCount` — a field the CNC did not report (refused sub-read, payload without an O-number) reads `BadNoData`, never `0` | `cnc_exeprgname2` + `cnc_rdblkcount` + cached `cnc_rddynamic2` |
 | `OperationMode/` | `Mode` (int), `ModeText` ("AUTO", "MDI", "EDIT", …) | `cnc_rdopmode` |
 | `Timers/` | `PowerOnSeconds`, `OperatingSeconds`, `CuttingSeconds`, `CycleSeconds` | `cnc_rdtimer` × 4 |
 
@@ -228,27 +233,29 @@ per-axis `ServoLoad` independently. Identity + `Axes/*` position reads
 (which every Fanuc CNC supports) are always emitted.
 
 Position values (`AbsolutePosition`, `MachinePosition`, `RelativePosition`, `DistanceToGo`)
-are CNC-internal scaled integers exposed as `Float64` OPC UA nodes. The driver converts them
-to engineering units using the per-device `PositionDecimalPlaces` config field (default `0`
-= no scaling). When set to a positive integer *d*, each position value is divided by `10^d`
-before publishing, so a CNC that reports millimetres × 1000 is corrected by setting
-`PositionDecimalPlaces: 3`.
+are published as `Float64` in engineering units. **Each `cnc_rddynamic2` position block carries
+its own scale** — `[i32 raw][u16 base][u16 exponent]`, value = `raw / base^exponent` (a real
+31i-B reports base 10 / exponent 4: `2801574` → `280.1574` mm) — and the driver always applies
+it. A block that describes no usable position (the `0xFFFF` vacant-slot marker, a base other
+than 2 or 10, an exponent > 18) publishes `BadNoData` on that node alone.
+
+`PositionDecimalPlaces` (per device, default `0`) is now only the **fallback for a block that
+carries no scale** (a 4-byte payload, e.g. an older simulator): such a position is divided by
+`10^PositionDecimalPlaces`. Negative values are clamped to `0`.
 
 ```jsonc
 "Devices": [
   {
     "HostAddress": "focas://10.20.30.40:8193",
     "Series": "ThirtyOne_i",
-    "PositionDecimalPlaces": 3   // 123456 → 123.456 mm
+    "PositionDecimalPlaces": 3   // only used if the CNC's blocks carry no scale
   }
 ]
 ```
 
-The driver now attempts to auto-scale each axis position using the CNC's `cnc_getfigure` figure when available; `PositionDecimalPlaces` is the **per-axis fallback** used only when the CNC reports no figure for that axis. **Caveat:** the managed `WireFocasClient` (FOCAS/2 Ethernet wire protocol) does not issue `cnc_getfigure` today, so on real hardware all axes still fall back to the manual `PositionDecimalPlaces` config field. Live auto-fetch is a follow-up requiring a `cnc_getfigure` command in `FocasWireClient`. Negative values from `PositionDecimalPlaces` are clamped to `0`.
-
-**Follow-ups (known gaps, non-blocking):**
-- No upper-bound clamp on the figure magnitude returned by the CNC — a misbehaving figure could overflow `Math.Pow`; a max-figure guard should be added.
-- The negative-figure branch (falls back to manual `PositionDecimalPlaces`) is handled but not explicitly unit-tested.
+There is no `cnc_getfigure` read: the `0x00D3` command the driver used to send is not a FOCAS
+wire command (a real 31i-B refuses it with `rc=1`), so on hardware every axis had silently
+fallen back to `PositionDecimalPlaces` and published raw counts.
 
 **Still hand-authored**: `PARAM:6711`, `MACRO:500`, `R100` etc. — specific
 numbers whose meaning is MTB-specific, and which no browse can discover. Those
@@ -330,7 +337,34 @@ latency spike once per cadence.
 | Every read returns `BadNotWritable` on writes | Expected — OtOpcUa is read-only against FOCAS | If you actually need writes, open a feature request — the driver's managed wire client doesn't expose the write commands |
 | `BadOutOfRange` on reads for a macro/parameter | Config address outside the declared `Series` range | Check `docs/v2/focas-version-matrix.md` — either fix the address or widen the `Series` |
 | Alarm events never fire | `AlarmProjection.Enabled` left at default (false) | Set it to `true` in the driver config |
-| Axis position values seem 1000× too large | `PositionDecimalPlaces` not set | Add `"PositionDecimalPlaces": 3` (or the MTB-specific value) to the device entry in `Devices[]` |
+| Axis position values seem 1000× too large | The CNC's position blocks carry no scale (older control / simulator) and `PositionDecimalPlaces` is not set | Add `"PositionDecimalPlaces": 3` (or the MTB-specific value) to the device entry in `Devices[]`. A real 30i/31i carries the scale in each block and needs no setting |
+| A fixed-tree node or `MACRO:` tag reads `BadNoData` | The CNC answered but described no value — a vacant macro variable, an undescribable position/meter record, a program field it did not report | Check the address on the control; this is the control's answer, not a comms fault |
+| An integer-typed `MACRO:` tag reads `BadTypeMismatch` | The macro holds a fractional value (e.g. `148.5`) | Author the tag as `Float64`, or point it at a whole-valued variable — a fraction is never truncated into an integer tag |
+
+## Wire decode corrections (2026-10)
+
+Each of these decoded without ever failing — just wrongly — so live validation that only checked
+"the read succeeds" passed them. All were found by the sister **ignitionoee** FOCAS driver
+against a real Makino 31i-B (Z-34184, series G431) and ported here with its captured payloads as
+test fixtures (`tests/.../Driver.FOCAS.Tests/Fixtures/v3/`). Client-visible changes are marked ⚠️.
+
+| What | Before | Now |
+|------|--------|-----|
+| `cnc_rdmacro` decimal | read at payload offset 4 — a constant `10` length field — so `#500 = 1.0` published `0.01` | `dec_val` at offset 6; `mantissa / 10^dec`. Vacant variable → `BadNoData`; fractional value on an integer tag → `BadTypeMismatch`; integer tags receive the exact whole value |
+| Axis positions | scaled by `cnc_getfigure` (0x00D3), which does not exist — on hardware: raw counts | scaled by each block's own `base^exponent`; undescribable block → `BadNoData` |
+| Axis / spindle names | first 2 of 4 record bytes — `AA6`/`AA7` collapsed to `AA` | whole record up to the first NUL (residue after it discarded) — ⚠️ `Axes/AA_1`→`Axes/AA6` on such a machine |
+| `ServoLoad` | `value / 10^base` (offset 4 is the base, 10) — always ~0 | `value / base^exponent`, a direct percentage |
+| `Spindle/{n}/Load` | raw meter count, Int32 (`9155`) | ⚠️ Float64 % of rated load (`55.9`): the meter is a 1/16384 fraction of full scale |
+| `Spindle/{n}/MaxRpm` | the type-1 meter read once at bootstrap and served as a "max RPM" | ⚠️ **renamed `MotorSpeedPct`**, Float64 % of maximum speed, polled every tick |
+| Program `ONumber` / `Name` / `BlockCount` / `Mode` | defaulted to `0` / `""` when not reported (Mode `0` = MDI) | `BadNoData` |
+
+Not ported (and why): the ignitionoee `RunState` run-word decode and fault debounce (this driver
+publishes no run-state — `cnc_statinfo` is used only as the connectivity probe); `cnc_rdparam3`
+(0x008D) and its echo guard (this driver never sends 0x008D — the real 31i-B answers it with
+264-byte records that are not a parameter read); the IODBPSD-offset and Fanuc-real `FLOAT`
+re-interpretation of `cnc_rdparam` (no successful `cnc_rdparam` capture exists on either side —
+the reference 31i-B refuses it with `EW_FUNC`, which already reads `BadNotSupported` here); and
+the all-axes multi-block `cnc_rddynamic2` batching (a latency optimisation, not a correctness fix).
 
 ## Further reading
 
diff --git a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Contracts/FocasDriverOptions.cs b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Contracts/FocasDriverOptions.cs
index da05b679..7929cf98 100644
--- a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Contracts/FocasDriverOptions.cs
+++ b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Contracts/FocasDriverOptions.cs
@@ -132,12 +132,11 @@ public sealed class FocasAlarmProjectionOptions
 ///     default) to skip range validation and preserve legacy behaviour.
 /// </param>
 /// <param name="PositionDecimalPlaces">
-///     Axis positions returned by <c>cnc_rddynamic2</c> are scaled integers. The driver
-///     divides AbsolutePosition / MachinePosition / RelativePosition / DistanceToGo by
-///     <c>10^PositionDecimalPlaces</c> at the publish seam so they surface in engineering
-///     units on the Float64 axis nodes. Default <c>0</c> (no scaling) is byte-identical to
-///     legacy behaviour. Auto-fetching this via <c>cnc_getfigure</c> is deferred (wire-gated),
-///     so it is config-supplied. Negative values are clamped to 0 (no scaling).
+///     <b>Fallback only.</b> A real CNC's <c>cnc_rddynamic2</c> position block carries its own
+///     scale (<c>raw / base^exponent</c>), which the driver always applies and which wins over
+///     this setting. Only a block that carries no scale (a 4-byte payload, e.g. an older
+///     simulator) is divided by <c>10^PositionDecimalPlaces</c>. Default <c>0</c> (no scaling).
+///     Negative values are clamped to 0.
 /// </param>
 public sealed record FocasDeviceOptions(
     string HostAddress,
diff --git a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FixedTreeNames.cs b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FixedTreeNames.cs
index 2666310d..e614146e 100644
--- a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FixedTreeNames.cs
+++ b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FixedTreeNames.cs
@@ -41,11 +41,18 @@ namespace ZB.MOM.WW.OtOpcUa.Driver.FOCAS;
 ///     config redeploy).
 ///     </para>
 ///     <para>
-///     Suffix collisions with genuine names are structurally impossible for axes (FOCAS axis
-///     displays are at most two characters — name + suffix — so they cannot contain <c>_</c>),
-///     but the generator still checks: a generated segment that would collide with anything
-///     else in the set escalates its ordinal until unique, so the output is always
-///     collision-free whatever the input.
+///     Suffix collisions with genuine names are not expected (a FOCAS name record is at most four
+///     ASCII characters and controls do not use <c>_</c>), but the generator still checks: a
+///     generated segment that would collide with anything else in the set escalates its ordinal
+///     until unique, so the output is always collision-free whatever the input.
+///     </para>
+///     <para>
+///     <b>Note on the Makino that motivated this.</b> Its two "AA" axes were a decode artefact:
+///     the name records actually read <c>"AA6"</c> and <c>"AA7"</c>, and the wire layer read only
+///     the first two bytes of each 4-byte record. With the full record decoded
+///     (<see cref="Wire.FocasWireProtocol.ReadNameRecord"/>) that machine reports unique names and
+///     its axes publish bare (<c>Axes/AA6</c>, <c>Axes/AA7</c>). This disambiguation remains as the
+///     guard for a control that genuinely reports duplicates.
 ///     </para>
 /// </remarks>
 internal static class FixedTreeNames
diff --git a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FocasDriver.cs b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FocasDriver.cs
index ea5acf3b..bbf4d0e9 100644
--- a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FocasDriver.cs
+++ b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FocasDriver.cs
@@ -643,7 +643,8 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
 
                 // Spindle subtree — one folder per discovered spindle, suppressed
                 // entirely on series that don't export cnc_rdspdlname. Per-spindle
-                // Load + MaxRpm each gated on their own capability probe.
+                // Load + MotorSpeedPct (both cnc_rdspmeter percentages of full scale)
+                // each gated on their own capability probe.
                 if (cache.Capabilities.Spindles)
                 {
                     var spindleRoot = deviceFolder.Folder("Spindle", "Spindle");
@@ -652,9 +653,9 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
                         var name = cache.SpindleSegments[i];
                         var spindleFolder = spindleRoot.Folder(name, name);
                         if (cache.Capabilities.SpindleLoad)
-                            EmitFixedVariable(spindleFolder, $"Spindle/{name}", "Load", DriverDataType.Int32);
-                        if (cache.Capabilities.SpindleMaxRpm && i < cache.SpindleMaxRpms.Count)
-                            EmitFixedVariable(spindleFolder, $"Spindle/{name}", "MaxRpm", DriverDataType.Int32);
+                            EmitFixedVariable(spindleFolder, $"Spindle/{name}", "Load", DriverDataType.Float64);
+                        if (cache.Capabilities.SpindleMotorSpeed)
+                            EmitFixedVariable(spindleFolder, $"Spindle/{name}", "MotorSpeedPct", DriverDataType.Float64);
                     }
                 }
 
@@ -925,15 +926,9 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
                 var sys = await client.GetSysInfoAsync(ct).ConfigureAwait(false);
                 var axes = await client.GetAxisNamesAsync(ct).ConfigureAwait(false);
 
-                // Per-axis decimal-place figures (cnc_getfigure), fetched once. Auto figures win
-                // over the manual PositionDecimalPlaces config at the publish seam; an empty list
-                // (or a failed/empty figure read) makes every axis fall back to the config knob.
-                // Defensive: a figure-read failure must NOT fault device init — default to empty.
-                state.PositionFigures = await SafeProbe(() => client.GetPositionFiguresAsync(ct), []);
-
                 // Optional-API probes — each returns empty / throws when unsupported.
                 var spindles = await SafeProbe(() => client.GetSpindleNamesAsync(ct), []);
-                var spindleMaxRpms = await SafeProbe(() => client.GetSpindleMaxRpmsAsync(ct), []);
+                var spindleMotorSpeeds = await SafeProbe(() => client.GetSpindleMotorSpeedsAsync(ct), []);
                 var servoLoads = await SafeProbe(() => client.GetServoLoadsAsync(ct), []);
                 var programInfo = await SafeTryProbe(() => client.GetProgramInfoAsync(ct));
                 var timer = await SafeTryProbe(() => client.GetTimerAsync(FocasTimerKind.PowerOn, ct));
@@ -942,13 +937,12 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
                 var caps = new FocasFixedTreeCapabilities(
                     Spindles: spindles.Count > 0,
                     SpindleLoad: spindleLoad.Count > 0,
-                    SpindleMaxRpm: spindleMaxRpms.Count > 0,
+                    SpindleMotorSpeed: spindleMotorSpeeds.Count > 0,
                     ServoLoad: servoLoads.Count > 0,
                     ProgramInfo: programInfo is not null,
                     Timers: timer is not null);
 
-                state.FixedTreeCache = new FocasFixedTreeCache(
-                    sys, [.. axes], [.. spindles], [.. spindleMaxRpms], caps);
+                state.FixedTreeCache = new FocasFixedTreeCache(sys, [.. axes], [.. spindles], caps);
                 // The bootstrap IS an answer from the device, and Identity comes entirely from it —
                 // so stamp liveness here as well as per tick, or a CNC whose axis poll never
                 // succeeds would serve a perfectly valid sysinfo as stale.
@@ -964,15 +958,14 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
             }
         }
 
-        // Prime the spindle-loads cache from bootstrap if supported — avoids a
+        // Prime the spindle-meter caches from bootstrap if supported — avoids a
         // "tree is there but reads say BadNodeIdUnknown" window on startup.
-        if (state.FixedTreeCache?.Capabilities is { SpindleLoad: true })
+        if (state.FixedTreeCache?.Capabilities is { SpindleLoad: true } or { SpindleMotorSpeed: true })
         {
             try
             {
                 var client2 = await EnsureConnectedAsync(state, ct).ConfigureAwait(false);
-                var loads = await client2.GetSpindleLoadsAsync(ct).ConfigureAwait(false);
-                for (var i = 0; i < loads.Count; i++) state.LastSpindleLoads[i] = loads[i];
+                await PollSpindleMetersAsync(state, client2, ct).ConfigureAwait(false);
             }
             catch (Exception ex)
             {
@@ -999,7 +992,7 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
                     var snap = await client.ReadDynamicAsync(axisIndex, ct).ConfigureAwait(false);
                     // Keyed by the disambiguated segment, matching what DiscoverAsync emitted —
                     // two same-named axes must not share (and overwrite) one cache slot (#548).
-                    PublishAxisSnapshot(state, cache.AxisSegments[i], snap, i); // i = 0-based axis index → PositionFigures lookup
+                    PublishAxisSnapshot(state, cache.AxisSegments[i], snap);
                     if (i == 0) { firstAxisSnap = snap; PublishRateSnapshot(state, snap); }
                 }
 
@@ -1025,17 +1018,16 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
                             state.Options.HostAddress);
                     }
                 }
-                if (cache.Capabilities.SpindleLoad)
+                if (cache.Capabilities.SpindleLoad || cache.Capabilities.SpindleMotorSpeed)
                 {
                     try
                     {
-                        var loads = await client.GetSpindleLoadsAsync(ct).ConfigureAwait(false);
-                        for (var i = 0; i < loads.Count; i++) state.LastSpindleLoads[i] = loads[i];
+                        await PollSpindleMetersAsync(state, client, ct).ConfigureAwait(false);
                     }
                     catch (Exception ex)
                     {
                         /* transient */
-                        _logger.LogDebug(ex, "FOCAS spindle-loads poll failed for {Host}",
+                        _logger.LogDebug(ex, "FOCAS spindle-meter poll failed for {Host}",
                             state.Options.HostAddress);
                     }
                 }
@@ -1102,40 +1094,34 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
     ///     <see cref="PollGroupEngine"/> → <see cref="ReadAsync"/> path, which hits
     ///     <see cref="TryReadFixedTree"/> and returns these cached values.
     /// </summary>
-    private static void PublishAxisSnapshot(DeviceState state, string axisSegment, FocasDynamicSnapshot snap, int axisIndex)
+    private static void PublishAxisSnapshot(DeviceState state, string axisSegment, FocasDynamicSnapshot snap)
     {
         var host = state.Options.HostAddress;
-        // cnc_rddynamic2 returns positions as scaled integers; divide by 10^figures so they
-        // surface in engineering units on the Float64 axis nodes. The figure is per-axis:
-        // an auto cnc_getfigure figure WINS, and the configured PositionDecimalPlaces is the
-        // fallback when the CNC didn't report one for that axis (see AxisFactor). A figure of
-        // 0 yields factor 1.0 — i.e. the integer widened to double, byte-identical to legacy
-        // behaviour (12345 / 1.0 == 12345.0). The managed WireFocasClient fetches figures live
-        // via ReadPositionFiguresAsync; the config knob is the per-axis fallback only. FeedRate /
+        // Each cnc_rddynamic2 position block carries its OWN scale (raw / base^exponent — see
+        // FocasPosition), so positions surface in engineering units with no second read; the
+        // configured PositionDecimalPlaces applies only to a block that carried no scale. A block
+        // describing no usable position (vacant 0xFFFF marker, odd base, absurd exponent) is
+        // cached as NaN and read back as BadNoData for that node alone (see NoValue). FeedRate /
         // SpindleSpeed (rate snapshot) and ServoLoad are NOT position-scaled (published elsewhere).
-        var factor = AxisFactor(state, axisIndex);
-        state.LastFixedSnapshots[FixedTreeReference(host, $"Axes/{axisSegment}/AbsolutePosition")] = snap.AbsolutePosition / factor;
-        state.LastFixedSnapshots[FixedTreeReference(host, $"Axes/{axisSegment}/MachinePosition")] = snap.MachinePosition / factor;
-        state.LastFixedSnapshots[FixedTreeReference(host, $"Axes/{axisSegment}/RelativePosition")] = snap.RelativePosition / factor;
-        state.LastFixedSnapshots[FixedTreeReference(host, $"Axes/{axisSegment}/DistanceToGo")] = snap.DistanceToGo / factor;
+        var dp = state.Options.PositionDecimalPlaces;
+        state.LastFixedSnapshots[FixedTreeReference(host, $"Axes/{axisSegment}/AbsolutePosition")] = snap.AbsolutePosition.ToEngineering(dp) ?? NoValue;
+        state.LastFixedSnapshots[FixedTreeReference(host, $"Axes/{axisSegment}/MachinePosition")] = snap.MachinePosition.ToEngineering(dp) ?? NoValue;
+        state.LastFixedSnapshots[FixedTreeReference(host, $"Axes/{axisSegment}/RelativePosition")] = snap.RelativePosition.ToEngineering(dp) ?? NoValue;
+        state.LastFixedSnapshots[FixedTreeReference(host, $"Axes/{axisSegment}/DistanceToGo")] = snap.DistanceToGo.ToEngineering(dp) ?? NoValue;
     }
 
     /// <summary>
-    ///     Resolve the position-scale factor (10^figure) for a single axis. Auto
-    ///     (<c>cnc_getfigure</c>) wins per-axis; manual <c>PositionDecimalPlaces</c> is the
-    ///     fallback when the CNC didn't report a figure for that axis. Both clamp non-negative;
-    ///     0 ⇒ factor 1.0 (legacy byte-identical). The managed wire backend fetches figures live
-    ///     via <c>ReadPositionFiguresAsync</c>; the fallback branch fires only when the CNC
-    ///     reports no figure for a given axis (or the figure read returns empty).
+    ///     Cache sentinel for "the CNC answered, but this field holds no usable value" (an
+    ///     undescribable position / meter record). The read path turns it into
+    ///     <see cref="FocasStatusMapper.BadNoData"/> for that node only — never a Good number.
     /// </summary>
-    private static double AxisFactor(DeviceState state, int axisIndex)
-    {
-        var figures = state.PositionFigures;
-        var dp = axisIndex >= 0 && axisIndex < figures.Count && figures[axisIndex] >= 0
-            ? figures[axisIndex]
-            : Math.Max(0, state.Options.PositionDecimalPlaces);
-        return dp > 0 ? Math.Pow(10, dp) : 1.0;
-    }
+    private const double NoValue = double.NaN;
+
+    /// <summary>Builds the snapshot for one cached double, mapping <see cref="NoValue"/> to BadNoData.</summary>
+    private static DataValueSnapshot CachedDouble(double value, uint status, DateTime sourceUtc, DateTime now) =>
+        double.IsNaN(value)
+            ? new DataValueSnapshot(null, status == FocasStatusMapper.Good ? FocasStatusMapper.BadNoData : status, sourceUtc, now)
+            : new DataValueSnapshot(value, status, sourceUtc, now);
 
     private static void PublishRateSnapshot(DeviceState state, FocasDynamicSnapshot snap)
     {
@@ -1160,7 +1146,27 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
     {
         var segments = FixedTreeNames.Disambiguate(loads.Select(l => l.AxisName));
         for (var i = 0; i < loads.Count; i++)
-            state.LastServoLoads[segments[i]] = loads[i].LoadPercent;
+            state.LastServoLoads[segments[i]] = loads[i].LoadPercent ?? NoValue;
+    }
+
+    /// <summary>
+    ///     Read and cache both spindle meters (load, motor speed) — each a <c>cnc_rdspmeter</c>
+    ///     percentage of full scale (16384 = 100%) — for every spindle slot, as capability allows.
+    ///     A slot whose record describes no value is cached as <see cref="NoValue"/> (BadNoData).
+    /// </summary>
+    private static async Task PollSpindleMetersAsync(DeviceState state, IFocasClient client, CancellationToken ct)
+    {
+        var caps = state.FixedTreeCache?.Capabilities;
+        if (caps is { SpindleLoad: true })
+        {
+            var loads = await client.GetSpindleLoadsAsync(ct).ConfigureAwait(false);
+            for (var i = 0; i < loads.Count; i++) state.LastSpindleLoads[i] = loads[i] ?? NoValue;
+        }
+        if (caps is { SpindleMotorSpeed: true })
+        {
+            var speeds = await client.GetSpindleMotorSpeedsAsync(ct).ConfigureAwait(false);
+            for (var i = 0; i < speeds.Count; i++) state.LastSpindleMotorSpeeds[i] = speeds[i] ?? NoValue;
+        }
     }
 
     private static object? TimerValue(DeviceState state, FocasTimerKind kind) =>
@@ -1241,7 +1247,7 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
 
         if (state.LastFixedSnapshots.TryGetValue(
                 FixedTreeReference(state.Options.HostAddress, path), out var raw))
-            return new DataValueSnapshot(raw, status, sourceUtc, now);
+            return CachedDouble(raw, status, sourceUtc, now);
 
         // Servo-load match: path shape is "Axes/{name}/ServoLoad"
         var suffixFull = path;
@@ -1249,10 +1255,10 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
         {
             var axisName = suffixFull["Axes/".Length..^"/ServoLoad".Length];
             if (state.LastServoLoads.TryGetValue(axisName, out var load))
-                return new DataValueSnapshot(load, status, sourceUtc, now);
+                return CachedDouble(load, status, sourceUtc, now);
         }
 
-        // Spindle matches: "Spindle/{name}/Load" + "Spindle/{name}/MaxRpm"
+        // Spindle matches: "Spindle/{name}/Load" + "Spindle/{name}/MotorSpeedPct"
         if (suffixFull.StartsWith("Spindle/", StringComparison.Ordinal)
             && state.FixedTreeCache is { } spindleCache)
         {
@@ -1271,14 +1277,14 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
                 }
                 if (idx >= 0)
                 {
-                    object? value = field switch
+                    var meters = field switch
                     {
-                        "Load" => state.LastSpindleLoads.TryGetValue(idx, out var l) ? (object)l : null,
-                        "MaxRpm" => idx < spindleCache.SpindleMaxRpms.Count ? (object)spindleCache.SpindleMaxRpms[idx] : null,
+                        "Load" => state.LastSpindleLoads,
+                        "MotorSpeedPct" => state.LastSpindleMotorSpeeds,
                         _ => null,
                     };
-                    if (value is not null)
-                        return new DataValueSnapshot(value, status, sourceUtc, now);
+                    if (meters is not null && meters.TryGetValue(idx, out var pct))
+                        return CachedDouble(pct, status, sourceUtc, now);
                 }
             }
         }
@@ -1301,8 +1307,8 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
                 "Program/MainNumber" => state.LastProgramAxisRef?.MainProgramNumber,
                 "Program/Sequence" => state.LastProgramAxisRef?.SequenceNumber,
                 "OperationMode/Mode" => state.LastProgramInfo?.Mode,
-                "OperationMode/ModeText" => state.LastProgramInfo is { } pi
-                    ? FocasOpMode.ToText(pi.Mode) : null,
+                "OperationMode/ModeText" => state.LastProgramInfo?.Mode is { } mode
+                    ? FocasOpMode.ToText(mode) : null,
                 "Timers/PowerOnSeconds" => TimerValue(state, FocasTimerKind.PowerOn),
                 "Timers/OperatingSeconds" => TimerValue(state, FocasTimerKind.Operating),
                 "Timers/CuttingSeconds" => TimerValue(state, FocasTimerKind.Cutting),
@@ -1311,6 +1317,18 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
             };
             if (value is not null)
                 return new DataValueSnapshot(value, status, sourceUtc, now);
+
+            // The program bundle has been read, but the CNC did not report this field (a refused
+            // sub-read, or no O-number in the payload). That is Bad — never a fabricated 0, and
+            // not "no such node" either.
+            if (state.LastProgramInfo is not null
+                && path is "Program/Name" or "Program/ONumber" or "Program/BlockCount"
+                    or "OperationMode/Mode" or "OperationMode/ModeText")
+                return new DataValueSnapshot(
+                    null,
+                    status == FocasStatusMapper.Good ? FocasStatusMapper.BadNoData : status,
+                    sourceUtc,
+                    now);
         }
         return null;
     }
@@ -1489,7 +1507,6 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
         FocasSysInfo SysInfo,
         IReadOnlyList<FocasAxisName> Axes,
         IReadOnlyList<FocasSpindleName> Spindles,
-        IReadOnlyList<int> SpindleMaxRpms,
         FocasFixedTreeCapabilities Capabilities)
     {
         /// <summary>
@@ -1515,14 +1532,14 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
     /// <summary>
     ///     Per-device optional-API capability flags — which of the "this may or may not
     ///     exist on this CNC series" calls succeeded at bootstrap. Drives per-series
-    ///     node suppression so a 16i that doesn't export <c>cnc_rdspmaxrpm</c> simply
-    ///     doesn't get a <c>Spindle/{name}/MaxRpm</c> node (instead of surfacing
+    ///     node suppression so a 16i that doesn't export <c>cnc_rdspmeter</c> simply
+    ///     doesn't get a <c>Spindle/{name}/MotorSpeedPct</c> node (instead of surfacing
     ///     <c>BadDeviceFailure</c> on every read).
     /// </summary>
     internal sealed record FocasFixedTreeCapabilities(
         bool Spindles,          // cnc_rdspdlname returned 1+ spindle names
-        bool SpindleLoad,       // cnc_rdspload bootstrap probe succeeded
-        bool SpindleMaxRpm,     // cnc_rdspmaxrpm bootstrap probe succeeded
+        bool SpindleLoad,       // cnc_rdspmeter type 0 (load) bootstrap probe succeeded
+        bool SpindleMotorSpeed, // cnc_rdspmeter type 1 (motor speed) bootstrap probe succeeded
         bool ServoLoad,         // cnc_rdsvmeter bootstrap probe returned data
         bool ProgramInfo,       // cnc_exeprgname2 + cnc_rdblkcount + cnc_rdopmode work
         bool Timers);           // cnc_rdtimer works for at least PowerOn
@@ -1578,9 +1595,10 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
         public DateTime? LastFixedPollUtc { get; set; }
         /// <summary>
         ///     Gets the last fixed-tree snapshots by field name. Double-typed so axis
-        ///     positions can carry the <c>10^PositionDecimalPlaces</c> engineering-unit
-        ///     scale applied at <see cref="PublishAxisSnapshot"/>; integer fields
-        ///     (feed rate, spindle speed) widen to double on store.
+        ///     positions can carry the engineering-unit scale applied at
+        ///     <see cref="PublishAxisSnapshot"/>; integer fields (feed rate, spindle speed) widen
+        ///     to double on store. <see cref="NoValue"/> (NaN) marks a field the CNC described as
+        ///     holding no value.
         /// </summary>
         public ConcurrentDictionary<string, double> LastFixedSnapshots { get; } = new(StringComparer.OrdinalIgnoreCase);
         /// <summary>Gets or sets the last program information snapshot.</summary>
@@ -1591,15 +1609,16 @@ public sealed class FocasDriver : IDriver, IReadable, IWritable, ITagDiscovery,
         public ConcurrentDictionary<FocasTimerKind, FocasTimer> LastTimers { get; } = new();
         /// <summary>Gets the last servo load percentages by servo name.</summary>
         public ConcurrentDictionary<string, double> LastServoLoads { get; } = new(StringComparer.OrdinalIgnoreCase);
-        /// <summary>Gets the last spindle load percentages by spindle index.</summary>
-        public ConcurrentDictionary<int, int> LastSpindleLoads { get; } = new();
         /// <summary>
-        ///     Gets or sets the per-axis position decimal-place figures fetched once at init via
-        ///     <c>cnc_getfigure</c> (parallel to the axis-name list; index = axis). An auto figure
-        ///     for an axis WINS over the configured <c>PositionDecimalPlaces</c>; an empty list (or
-        ///     a failed/empty figure read) makes every axis fall back to that config knob.
+        ///     Gets the last spindle load percentages (% of rated load) by spindle index;
+        ///     <see cref="NoValue"/> for a slot the CNC described as holding none.
         /// </summary>
-        public IReadOnlyList<int> PositionFigures { get; set; } = [];
+        public ConcurrentDictionary<int, double> LastSpindleLoads { get; } = new();
+        /// <summary>
+        ///     Gets the last spindle motor-speed percentages (% of maximum speed) by spindle index;
+        ///     <see cref="NoValue"/> for a slot the CNC described as holding none.
+        /// </summary>
+        public ConcurrentDictionary<int, double> LastSpindleMotorSpeeds { get; } = new();
 
         /// <summary>Disposes the FOCAS client instance.</summary>
         public void DisposeClient()
diff --git a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FocasDriverFactoryExtensions.cs b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FocasDriverFactoryExtensions.cs
index 8fbf4538..60a3a31f 100644
--- a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FocasDriverFactoryExtensions.cs
+++ b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FocasDriverFactoryExtensions.cs
@@ -290,9 +290,9 @@ public static class FocasDriverFactoryExtensions
         public string? Series { get; init; }
 
         /// <summary>
-        ///     Gets or sets the axis-position decimal places. <c>cnc_rddynamic2</c> returns
-        ///     positions as scaled integers; the driver divides by <c>10^PositionDecimalPlaces</c>
-        ///     so they surface in engineering units. Omitted / <c>0</c> = no scaling (legacy).
+        ///     Gets or sets the fallback axis-position decimal places, applied only to a
+        ///     <c>cnc_rddynamic2</c> position block that carries no scale of its own (a real CNC's
+        ///     block does, and its scale wins). Omitted / <c>0</c> = no scaling.
         /// </summary>
         public int? PositionDecimalPlaces { get; init; }
     }
diff --git a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FocasStatusMapper.cs b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FocasStatusMapper.cs
index 33f65bba..90fdcbf3 100644
--- a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FocasStatusMapper.cs
+++ b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/FocasStatusMapper.cs
@@ -19,6 +19,14 @@ public static class FocasStatusMapper
     public const uint BadTimeout = 0x800A0000u;
     public const uint BadTypeMismatch = 0x80740000u;
 
+    /// <summary>
+    ///     The CNC answered, but its answer describes no usable value — a vacant macro variable, a
+    ///     position / meter record whose own scale envelope is undecodable, a field the control did
+    ///     not report. Distinct from a comms fault (the device is fine) and never a fabricated
+    ///     Good <c>0</c>.
+    /// </summary>
+    public const uint BadNoData = 0x809B0000u;
+
     /// <summary>
     ///     Map common FWLIB <c>EW_*</c> return codes. The values below match Fanuc's published
     ///     numeric conventions (EW_OK=0, EW_FUNC=1, EW_NUMBER=3, EW_LENGTH=4, EW_ATTRIB=7,
diff --git a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/IFocasClient.cs b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/IFocasClient.cs
index 3242223e..2d5d8725 100644
--- a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/IFocasClient.cs
+++ b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/IFocasClient.cs
@@ -140,9 +140,10 @@ public interface IFocasClient : IDisposable
     // ---- Fixed-tree T3.5 (servo meters) ----
 
     /// <summary>
-    ///     Read the servo-load meter percentages across all configured axes.
-    ///     Values are percentages (scaled by <c>10^Dec</c>). Empty list on a
-    ///     disconnected session or unsupported CNC.
+    ///     Read the servo-load meter percentages across all configured axes. Each record's own
+    ///     <c>value / base^exponent</c> envelope is applied (servo loads are direct percentages);
+    ///     a record whose envelope describes no value carries a null <see cref="FocasServoLoad.LoadPercent"/>.
+    ///     Empty list on a disconnected session or unsupported CNC.
     /// </summary>
     /// <param name="cancellationToken">The cancellation token.</param>
     /// <returns>The servo-load meter percentages across all configured axes.</returns>
@@ -151,36 +152,31 @@ public interface IFocasClient : IDisposable
     // ---- Fixed-tree T3.6 (spindle meters) ----
 
     /// <summary>
-    ///     Read per-spindle load percentages. Result list index corresponds to
-    ///     spindle index from <see cref="GetSpindleNamesAsync"/>. Empty list on a
-    ///     disconnected session or when the CNC doesn't support the call (older
-    ///     series like 16i may return EW_FUNC).
+    ///     Read per-spindle load as a percentage of rated load (<c>cnc_rdspmeter</c> type 0; the
+    ///     raw meter is a 1/16384 fraction of full scale). Result list index corresponds to
+    ///     spindle index from <see cref="GetSpindleNamesAsync"/>; a slot whose record describes no
+    ///     value is null. Empty list on a disconnected session or when the CNC doesn't support the
+    ///     call (older series like 16i may return EW_FUNC).
     /// </summary>
     /// <param name="cancellationToken">The cancellation token.</param>
     /// <returns>Per-spindle load percentages, indexed as per <see cref="GetSpindleNamesAsync"/>.</returns>
-    Task<IReadOnlyList<int>> GetSpindleLoadsAsync(CancellationToken cancellationToken);
+    Task<IReadOnlyList<double?>> GetSpindleLoadsAsync(CancellationToken cancellationToken);
 
     /// <summary>
-    ///     Read per-spindle maximum RPM values. Static configuration, fetched once at
-    ///     bootstrap. Index alignment as per <see cref="GetSpindleLoadsAsync"/>.
+    ///     Read per-spindle motor speed as a percentage of maximum speed (<c>cnc_rdspmeter</c>
+    ///     type 1, historically labelled <c>cnc_rdspmaxrpm</c>). A live value, not a max-RPM
+    ///     constant. Index alignment and null semantics as per <see cref="GetSpindleLoadsAsync"/>.
     /// </summary>
     /// <param name="cancellationToken">The cancellation token.</param>
-    /// <returns>Per-spindle maximum RPM values, indexed as per <see cref="GetSpindleLoadsAsync"/>.</returns>
-    Task<IReadOnlyList<int>> GetSpindleMaxRpmsAsync(CancellationToken cancellationToken);
-
-    /// <summary>
-    ///     Read the per-axis position decimal-place figure via <c>cnc_getfigure</c>. The returned
-    ///     list is parallel to <see cref="GetAxisNamesAsync"/> (index = axis). An EMPTY list means the
-    ///     CNC/backend does not report figures — the driver then falls back to the configured
-    ///     <c>PositionDecimalPlaces</c>. Values are clamped non-negative.
-    /// </summary>
-    /// <param name="cancellationToken">The cancellation token.</param>
-    /// <returns>Per-axis position decimal-place figures; empty when the CNC/backend doesn't report them.</returns>
-    Task<IReadOnlyList<int>> GetPositionFiguresAsync(CancellationToken cancellationToken);
+    /// <returns>Per-spindle motor-speed percentages, indexed as per <see cref="GetSpindleLoadsAsync"/>.</returns>
+    Task<IReadOnlyList<double?>> GetSpindleMotorSpeedsAsync(CancellationToken cancellationToken);
 }
 
-/// <summary>One servo-meter entry — one axis's current load percentage.</summary>
-public sealed record FocasServoLoad(string AxisName, double LoadPercent);
+/// <summary>
+///     One servo-meter entry — one axis's current load percentage; null when the CNC's record
+///     described no usable value (never a fabricated 0).
+/// </summary>
+public sealed record FocasServoLoad(string AxisName, double? LoadPercent);
 
 /// <summary>Which cumulative counter <see cref="IFocasClient.GetTimerAsync"/> reads.</summary>
 public enum FocasTimerKind
@@ -238,22 +234,19 @@ public sealed record FocasSpindleName(string Name, string Suffix1, string Suffix
     }
 }
 
-/// <summary>
-///     Fast-poll bundle for one axis. Position values are scaled integers; the caller
-///     divides by <c>10^DecimalPlaces</c> to get the decimal value. DecimalPlaces is
-///     supplied by the caller — either via device config (<c>PositionDecimalPlaces</c>) or
-///     the per-axis <see cref="IFocasClient.GetPositionFiguresAsync"/> (<c>cnc_getfigure</c>) path.
-/// </summary>
 /// <summary>
 ///     Program + operation-mode snapshot. Name is the currently-executing
 ///     program filename (e.g. "O0001.NC"); ONumber is its Fanuc O-number (1-9999).
 ///     Mode is the numeric code from <c>cnc_rdopmode</c> — see <see cref="FocasOpMode"/>.
+///     <b>A null field means the CNC did not report it</b> (its sub-read was refused, or the
+///     payload was too short to carry it); the driver publishes that node Bad. It is never
+///     defaulted to <c>0</c>, which is a genuine O-number, block count, and mode (MDI).
 /// </summary>
 public sealed record FocasProgramInfo(
-    string Name,
-    int ONumber,
-    int BlockCount,
-    int Mode);
+    string? Name,
+    int? ONumber,
+    int? BlockCount,
+    int? Mode);
 
 /// <summary>Human-readable text for the <see cref="FocasProgramInfo.Mode"/> integer.</summary>
 public static class FocasOpMode
@@ -277,6 +270,10 @@ public static class FocasOpMode
     };
 }
 
+/// <summary>
+///     Fast-poll bundle for one axis (<c>cnc_rddynamic2</c>). Each position carries its own scale
+///     (see <see cref="FocasPosition"/>); the driver converts it to engineering units at publish.
+/// </summary>
 public sealed record FocasDynamicSnapshot(
     int AxisIndex,
     int AlarmFlags,
@@ -285,10 +282,60 @@ public sealed record FocasDynamicSnapshot(
     int SequenceNumber,
     int ActualFeedRate,
     int ActualSpindleSpeed,
-    int AbsolutePosition,
-    int MachinePosition,
-    int RelativePosition,
-    int DistanceToGo);
+    FocasPosition AbsolutePosition,
+    FocasPosition MachinePosition,
+    FocasPosition RelativePosition,
+    FocasPosition DistanceToGo);
+
+/// <summary>
+///     One <c>cnc_rddynamic2</c> position (command <c>0x0026</c>) as the CNC reported it. The 8-byte
+///     wire block is self-describing — <c>[0..3] i32 raw</c>, <c>[4..5] u16 base</c> (2 or 10),
+///     <c>[6..7] u16 exponent</c> (<c>0xFFFF</c> = the slot holds no valid position) — and the real
+///     coordinate is <c>raw / base^exponent</c>. Confirmed on a real FANUC 31i-B: every block of the
+///     <c>ref-dynamic2-axis1.bin</c> capture reports base 10 / exponent 4 (280.1574 mm, not
+///     2801574). That envelope is why no separate figure read exists: the <c>cnc_getfigure</c>
+///     (0x00D3) this driver used to send is not a FOCAS wire command, and the 31i-B refuses it.
+/// </summary>
+/// <param name="Raw">The raw i32 position value.</param>
+/// <param name="Base">The block's scale base (only 2 and 10 are meaningful).</param>
+/// <param name="Exponent">The block's scale exponent.</param>
+/// <param name="HasScale">
+///     True when the block carried the base/exponent envelope. A scale-less block (a 4-byte payload
+///     from an older simulator, or a raw integer a test supplies) falls back to the device's
+///     configured <c>PositionDecimalPlaces</c>.
+/// </param>
+public readonly record struct FocasPosition(int Raw, int Base = 0, int Exponent = 0, bool HasScale = false)
+{
+    /// <summary>
+    ///     False when the block says it holds no usable position: the <c>0xFFFF</c> vacant marker, a
+    ///     base other than 2 or 10, or an absurd exponent. A per-node quality decision — that node
+    ///     publishes Bad, its siblings are unaffected.
+    /// </summary>
+    /// <remarks>
+    ///     The exponent bound matters: left unbounded, <c>raw / 10^400</c> is
+    ///     <c>raw / Infinity = 0.0</c> — a Good reading of a machine parked at the origin.
+    /// </remarks>
+    public bool IsValid => !HasScale || Wire.FocasValueEnvelope.IsValid(Base, Exponent);
+
+    /// <summary>
+    ///     The position in engineering units: <c>Raw / Base^Exponent</c> when the block carried its
+    ///     own scale (the configured fallback is then ignored), else <c>Raw / 10^fallbackDecimalPlaces</c>.
+    ///     Null when <see cref="IsValid"/> is false.
+    /// </summary>
+    /// <param name="fallbackDecimalPlaces">The device's configured <c>PositionDecimalPlaces</c>.</param>
+    /// <returns>The scaled position, or null when the block describes none.</returns>
+    public double? ToEngineering(int fallbackDecimalPlaces)
+    {
+        if (!IsValid) return null;
+        if (HasScale) return Wire.FocasValueEnvelope.Scale(Raw, Base, Exponent);
+        var dp = Math.Max(0, fallbackDecimalPlaces);
+        return dp > 0 ? Raw / Math.Pow(10, dp) : Raw;
+    }
+
+    /// <summary>A bare integer is a scale-less position (legacy shape; tests and fakes).</summary>
+    /// <param name="raw">The raw position value.</param>
+    public static implicit operator FocasPosition(int raw) => new(raw);
+}
 
 /// <summary>
 ///     One active alarm surfaced by <see cref="IFocasClient.ReadAlarmsAsync"/>. Shape
diff --git a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/SynchronizedFocasClient.cs b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/SynchronizedFocasClient.cs
index 66010716..e2a3f759 100644
--- a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/SynchronizedFocasClient.cs
+++ b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/SynchronizedFocasClient.cs
@@ -99,16 +99,12 @@ public sealed class SynchronizedFocasClient : IFocasClient
         RunBoundedAsync(ct => _inner.GetServoLoadsAsync(ct), cancellationToken);
 
     /// <inheritdoc />
-    public Task<IReadOnlyList<int>> GetSpindleLoadsAsync(CancellationToken cancellationToken) =>
+    public Task<IReadOnlyList<double?>> GetSpindleLoadsAsync(CancellationToken cancellationToken) =>
         RunBoundedAsync(ct => _inner.GetSpindleLoadsAsync(ct), cancellationToken);
 
     /// <inheritdoc />
-    public Task<IReadOnlyList<int>> GetSpindleMaxRpmsAsync(CancellationToken cancellationToken) =>
-        RunBoundedAsync(ct => _inner.GetSpindleMaxRpmsAsync(ct), cancellationToken);
-
-    /// <inheritdoc />
-    public Task<IReadOnlyList<int>> GetPositionFiguresAsync(CancellationToken cancellationToken) =>
-        RunBoundedAsync(ct => _inner.GetPositionFiguresAsync(ct), cancellationToken);
+    public Task<IReadOnlyList<double?>> GetSpindleMotorSpeedsAsync(CancellationToken cancellationToken) =>
+        RunBoundedAsync(ct => _inner.GetSpindleMotorSpeedsAsync(ct), cancellationToken);
 
     /// <summary>Disposes the inner client and the call gate.</summary>
     public void Dispose()
diff --git a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/FocasWireClient.cs b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/FocasWireClient.cs
index 02dce813..097d210c 100644
--- a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/FocasWireClient.cs
+++ b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/FocasWireClient.cs
@@ -339,21 +339,59 @@ public sealed class FocasWireClient : IAsyncDisposable, IDisposable
         var rc = AggregateRc(blocks);
         if (rc != 0) return new FocasResult<WireDynamic>(rc, null);
 
+        return new FocasResult<WireDynamic>(rc, ParseDynamic2(blocks));
+    }
+
+    /// <summary>
+    ///     Aggregate the <c>cnc_rddynamic2</c> response blocks of one axis read into a
+    ///     <see cref="WireDynamic"/>. The four <c>0x0026</c> blocks are taken in request order
+    ///     (absolute / machine / relative / distance-to-go), each decoded with its own scale by
+    ///     <see cref="ParsePositionBlock"/>.
+    /// </summary>
+    /// <param name="blocks">The response blocks of one <see cref="ReadDynamic2Async"/> request.</param>
+    /// <returns>The decoded fast-poll bundle.</returns>
+    internal static WireDynamic ParseDynamic2(IReadOnlyList<ResponseBlock> blocks)
+    {
         var programPayload = FindPayload(blocks, 0x001c);
-        return new FocasResult<WireDynamic>(
-            rc,
-            new WireDynamic(
-                ReadFirstInt32(blocks, 0x001a),
-                programPayload.Length >= 4 ? ReadInt32(programPayload, 0) : 0,
-                programPayload.Length >= 8 ? ReadInt32(programPayload, 4) : 0,
-                ReadFirstInt32(blocks, 0x001d),
-                ReadFirstInt32(blocks, 0x0024),
-                ReadFirstInt32(blocks, 0x0025),
-                new WireAxisPosition(
-                    ReadSelectorPosition(blocks, 0x0026, 0),
-                    ReadSelectorPosition(blocks, 0x0026, 1),
-                    ReadSelectorPosition(blocks, 0x0026, 2),
-                    ReadSelectorPosition(blocks, 0x0026, 3))));
+        return new WireDynamic(
+            ReadFirstInt32(blocks, 0x001a),
+            programPayload.Length >= 4 ? ReadInt32(programPayload, 0) : 0,
+            programPayload.Length >= 8 ? ReadInt32(programPayload, 4) : 0,
+            ReadFirstInt32(blocks, 0x001d),
+            ReadFirstInt32(blocks, 0x0024),
+            ReadFirstInt32(blocks, 0x0025),
+            new WireAxisPosition(
+                ReadSelectorPosition(blocks, 0x0026, 0),
+                ReadSelectorPosition(blocks, 0x0026, 1),
+                ReadSelectorPosition(blocks, 0x0026, 2),
+                ReadSelectorPosition(blocks, 0x0026, 3)));
+    }
+
+    /// <summary>
+    ///     Decode one <c>cnc_rddynamic2</c> position block (0x0026). The 8-byte block is
+    ///     self-describing — <c>[0..3] i32 raw</c>, <c>[4..5] u16 base</c>, <c>[6..7] u16 exponent</c>,
+    ///     value = <c>raw / base^exponent</c> — pinned on a real FANUC 31i-B (every block of
+    ///     <c>ref-dynamic2-axis1.bin</c> reports base 10 / exponent 4). A 4..7-byte block carries no
+    ///     envelope and is returned scale-less (the driver then applies the configured
+    ///     <c>PositionDecimalPlaces</c>); a shorter one decodes as a scale-less 0, as before.
+    /// </summary>
+    /// <remarks>
+    ///     Validity (vacant <c>0xFFFF</c> exponent, a base other than 2/10, an absurd exponent) is a
+    ///     per-node quality decision made by <see cref="FocasPosition.IsValid"/>, not a fault here:
+    ///     raising would let one empty slot take out the whole poll. Ported from the sister
+    ///     ignitionoee driver v0.17.0 (<c>Dynamic2.scaledPosition</c>, Focas.Wire-014).
+    /// </remarks>
+    /// <param name="payload">The 0x0026 response-block payload.</param>
+    /// <returns>The position with whatever scale the block carried.</returns>
+    internal static FocasPosition ParsePositionBlock(byte[] payload)
+    {
+        if (payload.Length >= 8)
+            return new FocasPosition(
+                ReadInt32(payload, 0),
+                BinaryPrimitives.ReadUInt16BigEndian(payload.AsSpan(4, 2)),
+                BinaryPrimitives.ReadUInt16BigEndian(payload.AsSpan(6, 2)),
+                HasScale: true);
+        return new FocasPosition(payload.Length >= 4 ? ReadInt32(payload, 0) : 0);
     }
 
     /// <summary>Read servo-meter load percentages via <c>cnc_rdsvmeter</c> (command <c>0x0056</c>).</summary>
@@ -383,47 +421,14 @@ public sealed class FocasWireClient : IAsyncDisposable, IDisposable
     }
 
     /// <summary>
-    ///     Read the per-axis position decimal-place figures via <c>cnc_getfigure</c>
-    ///     (command <c>0x00d3</c>). The response payload is a self-delimiting sequence of
-    ///     big-endian <c>short</c> decimal-place counts — one per configured axis — which the
-    ///     driver applies as a <c>10^figure</c> scale on raw position reads.
+    ///     Read the per-spindle load meter via <c>cnc_rdspmeter</c> (command <c>0x0040</c>, type 0).
+    ///     <see cref="WireSpindleMetric.Percent"/> is % of rated load (16384 = 100%).
     /// </summary>
-    /// <remarks>
-    ///     The <c>0x00d3</c> command id is co-designed with the in-tree <c>focas_mock</c> sim and
-    ///     validated against it; like the rest of this managed wire backend the binary shape is
-    ///     sim-consistent and has not been validated against a real Fanuc CNC (bench-CNC-gated).
-    /// </remarks>
-    /// <param name="cancellationToken">Cancellation token for the read operation.</param>
-    /// <param name="timeout">Optional per-call timeout override.</param>
-    /// <param name="pathId">Optional path ID override; defaults to <see cref="PathId"/>.</param>
-    /// <returns>The per-axis position decimal-place figures, wrapped in a <see cref="FocasResult{T}"/>.</returns>
-    public async Task<FocasResult<IReadOnlyList<int>>> ReadPositionFiguresAsync(
-        CancellationToken cancellationToken = default,
-        TimeSpan? timeout = null,
-        ushort? pathId = null)
-    {
-        using var callTimeout = CreateCallTimeout(cancellationToken, timeout);
-        var requestPathId = EffectivePathId(pathId);
-        var block = await SendSingleRequestAsync(
-            callTimeout.Token,
-            new RequestBlock(0x00d3, PathId: requestPathId)).ConfigureAwait(false);
-
-        if (block.Rc != 0) return new FocasResult<IReadOnlyList<int>>(block.Rc, null);
-
-        var payload = block.Payload;
-        var figures = new List<int>(payload.Length / 2);
-        for (var offset = 0; offset + 2 <= payload.Length; offset += 2)
-            figures.Add(ReadInt16(payload, offset));
-
-        return new FocasResult<IReadOnlyList<int>>(block.Rc, figures);
-    }
-
-    /// <summary>Read per-spindle load percentages via <c>cnc_rdspload</c> (command <c>0x0040</c> with arg1=0).</summary>
     /// <param name="spindleSelector">Spindle selector; -1 selects all spindles.</param>
     /// <param name="cancellationToken">Cancellation token for the read operation.</param>
     /// <param name="timeout">Optional per-call timeout override.</param>
     /// <param name="pathId">Optional path ID override; defaults to <see cref="PathId"/>.</param>
-    /// <returns>The per-spindle load percentages, wrapped in a <see cref="FocasResult{T}"/>.</returns>
+    /// <returns>The per-spindle load meters, wrapped in a <see cref="FocasResult{T}"/>.</returns>
     public Task<FocasResult<IReadOnlyList<WireSpindleMetric>>> ReadSpindleLoadAsync(
         short spindleSelector = -1,
         CancellationToken cancellationToken = default,
@@ -431,13 +436,19 @@ public sealed class FocasWireClient : IAsyncDisposable, IDisposable
         ushort? pathId = null)
         => ReadSpindleMetricAsync(0, spindleSelector, cancellationToken, timeout, pathId);
 
-    /// <summary>Read per-spindle maximum RPMs via <c>cnc_rdspmaxrpm</c> (command <c>0x0040</c> with arg1=1).</summary>
+    /// <summary>
+    ///     Read the per-spindle motor-speed meter via <c>cnc_rdspmeter</c> (command <c>0x0040</c>,
+    ///     type 1 — historically labelled <c>cnc_rdspmaxrpm</c>). It is NOT a maximum-RPM constant:
+    ///     it is the live motor speed as a fraction of maximum, <see cref="WireSpindleMetric.Percent"/>
+    ///     (a regression against <c>cnc_rddynamic2</c> spindle speed on a real 31i-B gives
+    ///     <c>rpm = 1.220749 × meter</c>, i.e. 16384 = the spindle's 20,000 rpm maximum).
+    /// </summary>
     /// <param name="spindleSelector">Spindle selector; -1 selects all spindles.</param>
     /// <param name="cancellationToken">Cancellation token for the read operation.</param>
     /// <param name="timeout">Optional per-call timeout override.</param>
     /// <param name="pathId">Optional path ID override; defaults to <see cref="PathId"/>.</param>
-    /// <returns>The per-spindle maximum RPMs, wrapped in a <see cref="FocasResult{T}"/>.</returns>
-    public Task<FocasResult<IReadOnlyList<WireSpindleMetric>>> ReadSpindleMaxRpmAsync(
+    /// <returns>The per-spindle motor-speed meters, wrapped in a <see cref="FocasResult{T}"/>.</returns>
+    public Task<FocasResult<IReadOnlyList<WireSpindleMetric>>> ReadSpindleMotorSpeedAsync(
         short spindleSelector = -1,
         CancellationToken cancellationToken = default,
         TimeSpan? timeout = null,
@@ -577,9 +588,33 @@ public sealed class FocasWireClient : IAsyncDisposable, IDisposable
         ushort? pathId = null)
         => ReadSingleWithTimeoutAsync(
             0x0015,
-            payload => new WireMacro(number, payload.Length >= 4 ? ReadInt32(payload, 0) : 0, payload.Length >= 6 ? ReadInt16(payload, 4) : (short)0),
+            payload => ParseMacro(number, payload),
             cancellationToken, timeout, EffectivePathId(pathId), number, number);
 
+    /// <summary>
+    ///     Decode a <c>cnc_rdmacro</c> (0x0015) payload. The on-wire <c>ODBM</c> record is 8
+    ///     big-endian bytes: <c>[0..3] i32 mantissa</c>, <c>[4..5] i16</c> length field (a
+    ///     <b>constant 10</b> on every observed response), <c>[6..7] i16 dec_val</c>
+    ///     (<c>0xFFFF</c> = vacant).
+    /// </summary>
+    /// <remarks>
+    ///     The middle field is the trap: it is not the decimal count but looks like a plausible one,
+    ///     so reading the decimal at offset 4 decoded every macro on every control without ever
+    ///     failing — just wrongly (the captured <c>#500 = 1.0</c> published <c>0.01</c>). Pinned by
+    ///     a live Makino 31i-B capture; found and fixed by the sister ignitionoee driver
+    ///     (Focas.Wire-013, 2026-08-05). A payload shorter than 8 bytes carries no
+    ///     <c>dec_val</c> and is refused rather than guessed at.
+    /// </remarks>
+    /// <param name="number">The macro number the request asked for.</param>
+    /// <param name="payload">The response-block payload.</param>
+    /// <returns>The decoded macro.</returns>
+    /// <exception cref="FocasWireException">The payload is shorter than 8 bytes.</exception>
+    internal static WireMacro ParseMacro(short number, byte[] payload)
+    {
+        RequireLength(payload, 8, "cnc_rdmacro");
+        return new WireMacro(number, ReadInt32(payload, 0), ReadInt16(payload, 6));
+    }
+
     /// <summary>
     ///     Read a PMC range via <c>pmc_rdpmcrng</c>. <paramref name="area"/> is the numeric
     ///     address-letter code (see <see cref="FocasPmcArea"/>); <paramref name="dataType"/>
@@ -745,13 +780,27 @@ public sealed class FocasWireClient : IAsyncDisposable, IDisposable
             callTimeout.Token,
             new RequestBlock(0x0040, metric, spindleSelector, PathId: EffectivePathId(pathId))).ConfigureAwait(false);
 
-        return ToResult<IReadOnlyList<WireSpindleMetric>>(block, payload =>
-        {
-            var values = new List<WireSpindleMetric>();
-            for (var offset = 0; offset + 8 <= payload.Length; offset += 8)
-                values.Add(new WireSpindleMetric((short)(values.Count + 1), ReadInt32(payload, offset)));
-            return values;
-        });
+        return ToResult(block, ParseSpindleMetrics);
+    }
+
+    /// <summary>
+    ///     Decode a <c>cnc_rdspmeter</c> (0x0040) payload: 8-byte records of
+    ///     <c>[+0..3] i32 value</c>, <c>[+4..5] u16 base</c>, <c>[+6..7] u16 exponent</c>, one per
+    ///     slot of a fixed multi-slot buffer (slots past the spindle count are residue and decode
+    ///     as <see cref="WireSpindleMetric.IsValid"/> = false). Every slot is returned, in wire order.
+    /// </summary>
+    /// <param name="payload">The response-block payload.</param>
+    /// <returns>The per-slot meters.</returns>
+    internal static IReadOnlyList<WireSpindleMetric> ParseSpindleMetrics(byte[] payload)
+    {
+        var values = new List<WireSpindleMetric>();
+        for (var offset = 0; offset + 8 <= payload.Length; offset += 8)
+            values.Add(new WireSpindleMetric(
+                (short)(values.Count + 1),
+                ReadInt32(payload, offset),
+                BinaryPrimitives.ReadUInt16BigEndian(payload.AsSpan(offset + 4, 2)),
+                BinaryPrimitives.ReadUInt16BigEndian(payload.AsSpan(offset + 6, 2))));
+        return values;
     }
 
     private async Task<FocasResult<T>> ReadSingleAsync<T>(
@@ -932,18 +981,16 @@ public sealed class FocasWireClient : IAsyncDisposable, IDisposable
         payload.Length >= 8 ? BinaryPrimitives.ReadInt32LittleEndian(payload.AsSpan(4, 4)) : 0);
 
     /// <summary>
-    ///     Decode a <c>cnc_rdsvmeter</c> response into <see cref="WireServoMeter"/> records. On the
-    ///     31i-B (v3) each per-axis LOADELM is <b>8 bytes</b> — {int32 data; int16 dec; int16 unit}
-    ///     — NOT the 12-byte shape the original parser assumed. The 12-byte stride misaligned after
-    ///     the first record (it read the dec/unit shorts of the prior record as the next record's
-    ///     data → wild values like 655360). Axis NAMES are not in the svmeter payload; they come
-    ///     from the <c>cnc_rdaxisname</c> (0x0089) block requested alongside it and are correlated
-    ///     by index. Validated against a live 31i-B 2026-06-25.
-    ///     <para><b>Scaling caveat:</b> downstream applies LoadPercent = data / 10^dec; on the 31i-B
-    ///     <c>dec</c> read as 10, which makes idle loads vanishingly small. The data/dec/unit field
-    ///     semantics for servo load are inferred from the wire and not yet confirmed against the
-    ///     machine's servo-meter screen — confirm magnitude at commissioning. The alignment + name
-    ///     fix here is what removes the gross misaligned garbage.</para>
+    ///     Decode a <c>cnc_rdsvmeter</c> response into <see cref="WireServoMeter"/> records. Each
+    ///     per-axis record is <b>8 bytes</b> — <c>[+0..3] i32 value</c>, <c>[+4..5] u16 base</c>,
+    ///     <c>[+6..7] u16 exponent</c> — the same self-describing envelope as the position blocks,
+    ///     so the load is <c>value / base^exponent</c>, a direct percentage. (A 12-byte stride
+    ///     misaligned after the first record; reading offset 4 as a decimal count divided every load
+    ///     by 10^10 — both fixed against live 31i-B captures, the latter by the sister ignitionoee
+    ///     driver, Focas.Wire-019.) Axis NAMES are not in the svmeter payload; they come from the
+    ///     <c>cnc_rdaxisname</c> (0x0089) block requested alongside it and are correlated by index.
+    ///     The payload is a fixed 32-slot buffer: slots past the controlled-axis count are residue
+    ///     and decode as <see cref="WireServoMeter.IsValid"/> = false.
     /// </summary>
     /// <param name="svPayload">The raw <c>cnc_rdsvmeter</c> response payload.</param>
     /// <param name="axisNamePayload">The raw <c>cnc_rdaxisname</c> response payload used to correlate axis names by index.</param>
@@ -963,8 +1010,8 @@ public sealed class FocasWireClient : IAsyncDisposable, IDisposable
                 (short)(index + 1),
                 name,
                 ReadInt32(svPayload, offset),
-                ReadInt16(svPayload, offset + 4),
-                ReadInt16(svPayload, offset + 6)));
+                BinaryPrimitives.ReadUInt16BigEndian(svPayload.AsSpan(offset + 4, 2)),   // BASE, not a decimal
+                BinaryPrimitives.ReadUInt16BigEndian(svPayload.AsSpan(offset + 6, 2))));
         }
         return result;
     }
@@ -1020,17 +1067,17 @@ public sealed class FocasWireClient : IAsyncDisposable, IDisposable
         return payload.Length >= 4 ? ReadInt32(payload, 0) : 0;
     }
 
-    private static int ReadSelectorPosition(IReadOnlyList<ResponseBlock> blocks, ushort command, int selectorIndex)
+    private static FocasPosition ReadSelectorPosition(IReadOnlyList<ResponseBlock> blocks, ushort command, int selectorIndex)
     {
         var seen = 0;
         foreach (var block in blocks)
         {
             if (block.Command != command) continue;
             if (seen == selectorIndex)
-                return block.Payload.Length >= 4 ? ReadInt32(block.Payload, 0) : 0;
+                return ParsePositionBlock(block.Payload);
             seen++;
         }
-        return 0;
+        return new FocasPosition(0);
     }
 
     private static WireSysInfo ParseSysInfo(byte[] payload)
@@ -1090,7 +1137,17 @@ public sealed class FocasWireClient : IAsyncDisposable, IDisposable
         return alarms;
     }
 
-    private static IReadOnlyList<T> ReadNameRecords<T>(byte[] payload, short maxCount, Func<short, string, T> factory)
+    /// <summary>
+    ///     Decode an axis-name (0x0089) or spindle-name (0x008A) payload: an array of 4-byte records,
+    ///     each named by <see cref="FocasWireProtocol.ReadNameRecord"/>. Blank records are skipped but
+    ///     keep their slot's 1-based index.
+    /// </summary>
+    /// <typeparam name="T">The record type the factory builds.</typeparam>
+    /// <param name="payload">The response-block payload.</param>
+    /// <param name="maxCount">Maximum number of records to inspect.</param>
+    /// <param name="factory">Builds one record from its 1-based index and name.</param>
+    /// <returns>The non-blank records, in wire order.</returns>
+    internal static IReadOnlyList<T> ReadNameRecords<T>(byte[] payload, short maxCount, Func<short, string, T> factory)
     {
         var names = new List<T>();
         for (var offset = 0; offset + 4 <= payload.Length && offset / 4 < maxCount; offset += 4)
diff --git a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/FocasWireModels.cs b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/FocasWireModels.cs
index abdc1d74..844ea542 100644
--- a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/FocasWireModels.cs
+++ b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/FocasWireModels.cs
@@ -35,12 +35,15 @@ public sealed record WireStatus(
     short Edit,
     short TmMode);
 
-/// <summary>Four-slot position quadruple for one axis: absolute / machine / relative / distance-to-go.</summary>
+/// <summary>
+///     Four-slot position quadruple for one axis: absolute / machine / relative / distance-to-go,
+///     each carrying the scale its own <c>0x0026</c> block reported.
+/// </summary>
 public sealed record WireAxisPosition(
-    int Absolute,
-    int Machine,
-    int Relative,
-    int Distance);
+    FocasPosition Absolute,
+    FocasPosition Machine,
+    FocasPosition Relative,
+    FocasPosition Distance);
 
 /// <summary>
 ///     Fast-poll bundle for one axis from <c>cnc_rddynamic2</c> — alarm flags, active program
@@ -56,18 +59,104 @@ public sealed record WireDynamic(
     int SpindleSpeed,
     WireAxisPosition Axis);
 
-/// <summary>One servo-meter entry from <c>cnc_rdsvmeter</c> — per-axis load percentage (scale by 10^<see cref="Decimal"/>).</summary>
+/// <summary>
+///     The self-describing <c>(value, base, exponent)</c> envelope shared by every value record on
+///     the FOCAS wire — <c>cnc_rddynamic2</c> positions, servo meters, spindle meters:
+///     <c>scaled = value / base^exponent</c>, where only base 2 and base 10 are meaningful.
+/// </summary>
+internal static class FocasValueEnvelope
+{
+    /// <summary>
+    ///     Largest exponent that can describe a real value. An i32 carries at most ten digits, so
+    ///     anything beyond is a misread record — and <c>value / 10^400</c> would be
+    ///     <c>value / Infinity = 0.0</c>, a plausible Good zero.
+    /// </summary>
+    public const int MaxExponent = 18;
+
+    /// <summary>
+    ///     True when the record describes a usable value. A fixed multi-slot buffer's slots past the
+    ///     configured axis/spindle count hold unrelated memory, which shows up exactly here: a base
+    ///     that is neither 2 nor 10, or an absurd exponent (incl. the <c>0xFFFF</c> vacant marker).
+    /// </summary>
+    /// <param name="base">The record's base field.</param>
+    /// <param name="exponent">The record's exponent field.</param>
+    /// <returns>Whether the record may be published.</returns>
+    public static bool IsValid(int @base, int exponent) => exponent <= MaxExponent && @base is 2 or 10;
+
+    /// <summary><c>value / base^exponent</c>, or null when <see cref="IsValid"/> is false.</summary>
+    /// <param name="value">The raw value.</param>
+    /// <param name="base">The record's base field.</param>
+    /// <param name="exponent">The record's exponent field.</param>
+    /// <returns>The scaled value, or null.</returns>
+    public static double? Scale(int value, int @base, int exponent) =>
+        !IsValid(@base, exponent) ? null : exponent == 0 ? value : value / Math.Pow(@base, exponent);
+}
+
+/// <summary>
+///     One servo-meter entry from <c>cnc_rdsvmeter</c> (0x0056): one axis's load. The 8-byte record
+///     is <c>[+0..3] i32 value</c>, <c>[+4..5] u16 base</c>, <c>[+6..7] u16 exponent</c> and the load
+///     is a <b>direct</b> percentage, <see cref="Scaled"/> = <c>value / base^exponent</c>.
+/// </summary>
+/// <remarks>
+///     Offset 4 used to be read as a decimal count ("data / 10^dec"). It is the <b>base</b> — a
+///     steady 10 — so every load was divided by 10^10 and published ~0 (a real Makino cutting at
+///     20,000 rpm read servo 0% on every axis). Found by the sister ignitionoee driver,
+///     Focas.Wire-019 (v0.17.2).
+/// </remarks>
+/// <param name="Index">1-based axis slot.</param>
+/// <param name="Name">Axis name from the companion 0x0089 block (empty when none).</param>
+/// <param name="Value">Raw load value.</param>
+/// <param name="Base">Scale base (2 or 10 when meaningful).</param>
+/// <param name="Exponent">Scale exponent.</param>
 public sealed record WireServoMeter(
     short Index,
     string Name,
     int Value,
-    short Decimal,
-    short Unit);
+    int Base,
+    int Exponent)
+{
+    /// <summary>False for a record whose envelope describes no usable value (buffer residue).</summary>
+    public bool IsValid => FocasValueEnvelope.IsValid(Base, Exponent);
 
-/// <summary>One spindle metric slot from <c>cnc_rdspload</c> / <c>cnc_rdspmaxrpm</c>.</summary>
+    /// <summary>The load percentage, <c>Value / Base^Exponent</c>; null when <see cref="IsValid"/> is false.</summary>
+    public double? Scaled => FocasValueEnvelope.Scale(Value, Base, Exponent);
+}
+
+/// <summary>
+///     One spindle-meter slot from <c>cnc_rdspmeter</c> (0x0040; type 0 = load, type 1 = motor
+///     speed). Same 8-byte envelope as <see cref="WireServoMeter"/>, but the scaled value is a
+///     fraction of full scale in <c>1/16384</c> units — see <see cref="Percent"/>.
+/// </summary>
+/// <param name="Index">1-based spindle slot.</param>
+/// <param name="Value">Raw meter value, in 1/16384-of-full-scale units.</param>
+/// <param name="Base">Scale base.</param>
+/// <param name="Exponent">Scale exponent.</param>
 public sealed record WireSpindleMetric(
     short Index,
-    int Value);
+    int Value,
+    int Base,
+    int Exponent)
+{
+    /// <summary>
+    ///     The meter's full-scale count: <c>16384</c> = 2^14 = 100% of rated load (type 0) or of
+    ///     maximum spindle speed (type 1). Settled on the real Z-34184 by regressing the type-1
+    ///     meter against <c>cnc_rddynamic2</c> spindle speed over 596–20,000 rpm:
+    ///     <c>rpm = 1.220749 × meter</c>, <c>16384 × 1.220749 = 20000.75</c> (Focas.Wire-019).
+    /// </summary>
+    public const int FullScale = 1 << 14;
+
+    /// <summary>False for a record whose envelope describes no usable value (buffer residue).</summary>
+    public bool IsValid => FocasValueEnvelope.IsValid(Base, Exponent);
+
+    /// <summary>
+    ///     The meter as a percentage — <c>(Value / Base^Exponent) × 100 / 16384</c> — or null when
+    ///     <see cref="IsValid"/> is false. Values above 100 are real (short-term overload; the i16
+    ///     record clamps one count short of 200%).
+    /// </summary>
+    public double? Percent => FocasValueEnvelope.Scale(Value, Base, Exponent) is { } scaled
+        ? scaled * 100.0 / FullScale
+        : null;
+}
 
 /// <summary>
 ///     One axis-name slot from <c>cnc_rdaxisname</c>. <see cref="Index"/> is the 1-based
@@ -86,13 +175,31 @@ public sealed record WireParameter(
     int Value);
 
 /// <summary>
-///     Macro variable from <c>cnc_rdmacro</c>. Scaled decimal: the callable value is
-///     <c>Value / 10^Decimal</c>.
+///     Macro variable from <c>cnc_rdmacro</c>. Scaled decimal: the real value is
+///     <c>Value / 10^Decimal</c> (<see cref="Scaled"/>). FANUC normalises every macro to a
+///     9-significant-digit mantissa, so <see cref="Value"/> alone is never a value to publish
+///     (live: <c>#502 = 270</c> arrives as <c>270000000 / 10^6</c>).
 /// </summary>
+/// <param name="Number">Macro variable number (the request argument; not carried in the payload).</param>
+/// <param name="Value">The 9-significant-digit mantissa.</param>
+/// <param name="Decimal">Implied decimal places; negative (<c>0xFFFF</c> on the wire) = vacant.</param>
 public sealed record WireMacro(
     short Number,
     int Value,
-    short Decimal);
+    short Decimal)
+{
+    /// <summary>
+    ///     True when the CNC reported the variable as vacant (undefined / never set):
+    ///     <c>dec_val == 0xFFFF</c>. A vacant macro's mantissa is 0, indistinguishable from a
+    ///     genuine 0, so this must be tested before <see cref="Value"/> means anything. Any
+    ///     negative decimal is treated as vacant — no other negative has ever been observed and
+    ///     failing closed is the safe reading.
+    /// </summary>
+    public bool IsVacant => Decimal < 0;
+
+    /// <summary>The real value, <c>Value / 10^Decimal</c>; null when <see cref="IsVacant"/>.</summary>
+    public double? Scaled => IsVacant ? null : Decimal == 0 ? Value : Value / Math.Pow(10.0, Decimal);
+}
 
 /// <summary>PMC range read-back from <c>pmc_rdpmcrng</c>: one or more values of the requested width.</summary>
 public sealed record WirePmcRange(
diff --git a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/FocasWireProtocol.cs b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/FocasWireProtocol.cs
index 35df33d3..2c6b394e 100644
--- a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/FocasWireProtocol.cs
+++ b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/FocasWireProtocol.cs
@@ -239,19 +239,34 @@ internal static class FocasWireProtocol
     }
 
     /// <summary>
-    ///     Read an axis/spindle name record — the first 2 bytes of a 2-byte (axis) or 4-byte
-    ///     (spindle) slot. Trailing spaces and NULs are stripped so <c>"X "</c> becomes
-    ///     <c>"X"</c>.
+    ///     Read one 4-byte axis/spindle name record: the ASCII up to (not including) the record's
+    ///     FIRST NUL, at most 4 bytes, with trailing spaces trimmed — <c>"X \0\0"</c> → <c>"X"</c>,
+    ///     <c>"AA6\0"</c> → <c>"AA6"</c>, <c>"S1\0N"</c> → <c>"S1"</c>.
     /// </summary>
-    /// <param name="bytes">The bytes to decode.</param>
-    /// <returns>The decoded name record.</returns>
+    /// <remarks>
+    ///     <para><b>All four bytes are name bytes.</b> This used to read only the first two, which
+    ///     collapsed the real 31i-B's paired axes <c>"AA6"</c>/<c>"AA7"</c> (live capture
+    ///     <c>ref-axisname-0x0089.bin</c>) to two axes both called <c>"AA"</c> — the duplicate Gitea
+    ///     #548 then had to disambiguate as <c>AA_1</c>/<c>AA_2</c>.</para>
+    ///     <para><b>The first NUL terminates, not trailing-NUL trimming.</b> A control writes only the
+    ///     bytes its name needs and leaves the rest of the buffer as it found it: Makino Z-34184's
+    ///     <c>cnc_rdspdlname</c> answered <c>53 31 00 4e</c> — <c>"S1"</c> plus the <c>'N'</c> of an
+    ///     earlier <c>"CNC"</c> response. Both rules are ported from the sister ignitionoee FOCAS
+    ///     driver (Focas.Wire-001 / Focas.Wire-022).</para>
+    /// </remarks>
+    /// <param name="bytes">The record bytes (4 on the wire; a shorter span is read as far as it goes).</param>
+    /// <returns>The decoded name; empty for a blank record.</returns>
     public static string ReadNameRecord(ReadOnlySpan<byte> bytes)
     {
-        if (bytes.Length < 2) return string.Empty;
-        var buffer = bytes.Slice(0, Math.Min(2, bytes.Length)).ToArray();
-        return Encoding.ASCII.GetString(buffer).TrimEnd(' ', '\0');
+        var record = bytes.Slice(0, Math.Min(NameRecordLength, bytes.Length));
+        var nul = record.IndexOf((byte)0);
+        if (nul >= 0) record = record.Slice(0, nul);
+        return Encoding.ASCII.GetString(record).TrimEnd(' ');
     }
 
+    /// <summary>Byte length of one axis/spindle name record.</summary>
+    public const int NameRecordLength = 4;
+
     private static byte[] BuildRequestBlock(RequestBlock request)
     {
         var extra = request.ExtraPayload ?? Array.Empty<byte>();
diff --git a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/WireFocasClient.cs b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/WireFocasClient.cs
index bea99a40..acc104c1 100644
--- a/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/WireFocasClient.cs
+++ b/src/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS/Wire/WireFocasClient.cs
@@ -62,7 +62,7 @@ public sealed class WireFocasClient : IFocasClient
         {
             FocasAreaKind.Pmc => await ReadPmcAsync(address, type, cancellationToken).ConfigureAwait(false),
             FocasAreaKind.Parameter => await ReadParameterAsync(address, type, cancellationToken).ConfigureAwait(false),
-            FocasAreaKind.Macro => await ReadMacroAsync(address, cancellationToken).ConfigureAwait(false),
+            FocasAreaKind.Macro => await ReadMacroAsync(address, type, cancellationToken).ConfigureAwait(false),
             _ => (null, FocasStatusMapper.BadNotSupported),
         };
     }
@@ -181,6 +181,8 @@ public sealed class WireFocasClient : IFocasClient
         ThrowIfRcNonZero(result.Rc, "cnc_rddynamic2", result.IsOk);
         var d = result.Value!;
         var pos = d.Axis ?? new WireAxisPosition(0, 0, 0, 0);
+        // Positions keep the scale their own 0x0026 block reported; the driver converts them to
+        // engineering units at publish (FocasPosition.ToEngineering).
         return new FocasDynamicSnapshot(
             AxisIndex: axisIndex,
             AlarmFlags: d.Alarm,
@@ -215,12 +217,29 @@ public sealed class WireFocasClient : IFocasClient
             throw new InvalidOperationException(
                 $"cnc_exeprgname2 failed EW_{nameResult.Rc} and cnc_rdopmode failed EW_{modeResult.Rc}.");
 
-        var wireName = nameResult.Value;
+        return MapProgramInfo(nameResult, blkResult, modeResult);
+    }
+
+    /// <summary>
+    ///     Combine the three program sub-reads into a <see cref="FocasProgramInfo"/>, leaving any
+    ///     field the CNC did not report null. A refused read, or an <c>cnc_exeprgname2</c> payload
+    ///     too short to carry the trailing O-number, used to publish a fabricated <c>0</c> at Good
+    ///     quality — indistinguishable from a real 0 (a 31i reports O-number 0 for a program run
+    ///     by path) and, for the mode, from MDI. Ported from the sister ignitionoee driver (101a3b1).
+    /// </summary>
+    /// <param name="name">The <c>cnc_exeprgname2</c> result.</param>
+    /// <param name="blockCount">The <c>cnc_rdblkcount</c> result.</param>
+    /// <param name="mode">The <c>cnc_rdopmode</c> result.</param>
+    /// <returns>The snapshot, null where the CNC did not say.</returns>
+    internal static FocasProgramInfo MapProgramInfo(
+        FocasResult<WireProgramName> name, FocasResult<int> blockCount, FocasResult<short> mode)
+    {
+        var wireName = name.IsOk ? name.Value : null;
         return new FocasProgramInfo(
-            Name: wireName?.Name ?? string.Empty,
-            ONumber: wireName?.ONumber ?? 0,
-            BlockCount: blkResult.IsOk ? blkResult.Value : 0,
-            Mode: modeResult.IsOk ? modeResult.Value : 0);
+            Name: wireName?.Name,
+            ONumber: wireName?.ONumber,
+            BlockCount: blockCount.IsOk ? blockCount.Value : null,
+            Mode: mode.IsOk ? mode.Value : null);
     }
 
     /// <inheritdoc />
@@ -240,52 +259,32 @@ public sealed class WireFocasClient : IFocasClient
         var result = await _wire.ReadServoMeterAsync(32, cancellationToken).ConfigureAwait(false);
         if (!result.IsOk || result.Value is null) return [];
         return result.Value
-            .Select(m => new FocasServoLoad(m.Name ?? string.Empty, m.Value / Math.Pow(10.0, m.Decimal)))
+            .Select(m => new FocasServoLoad(m.Name ?? string.Empty, m.Scaled))
             .Where(s => s.AxisName.Length > 0)
             .ToList();
     }
 
     /// <inheritdoc />
-    public Task<IReadOnlyList<int>> GetSpindleLoadsAsync(CancellationToken cancellationToken) =>
+    public Task<IReadOnlyList<double?>> GetSpindleLoadsAsync(CancellationToken cancellationToken) =>
         ReadSpindleMetricAsync((sel, ct) => _wire.ReadSpindleLoadAsync(sel, ct), cancellationToken);
 
     /// <inheritdoc />
-    public Task<IReadOnlyList<int>> GetSpindleMaxRpmsAsync(CancellationToken cancellationToken) =>
-        ReadSpindleMetricAsync((sel, ct) => _wire.ReadSpindleMaxRpmAsync(sel, ct), cancellationToken);
+    public Task<IReadOnlyList<double?>> GetSpindleMotorSpeedsAsync(CancellationToken cancellationToken) =>
+        ReadSpindleMetricAsync((sel, ct) => _wire.ReadSpindleMotorSpeedAsync(sel, ct), cancellationToken);
 
-    /// <inheritdoc />
-    // Reads via FocasWireClient.ReadPositionFiguresAsync; returns an empty list when the read
-    // fails (non-zero RC — e.g. the series lacks cnc_getfigure) or is not connected. Never
-    // throws — figure reads degrade to the configured PositionDecimalPlaces rather than faulting.
-    public async Task<IReadOnlyList<int>> GetPositionFiguresAsync(CancellationToken cancellationToken)
-    {
-        if (!_wire.IsConnected) return [];
-        try
-        {
-            var result = await _wire.ReadPositionFiguresAsync(cancellationToken).ConfigureAwait(false);
-            return result.IsOk && result.Value is { } figures ? figures : [];
-        }
-        catch (FocasWireException)
-        {
-            return [];
-        }
-    }
-
-    private static async Task<IReadOnlyList<int>> ReadSpindleMetricAsync(
+    /// <summary>
+    ///     One <c>cnc_rdspmeter</c> read as per-slot percentages (null for an undescribable slot).
+    ///     Every slot is returned — the driver reads only the slots of discovered spindles. (This
+    ///     used to stop at the first zero after slot 1, which both dropped a genuinely idle second
+    ///     spindle and kept non-zero buffer residue.)
+    /// </summary>
+    private static async Task<IReadOnlyList<double?>> ReadSpindleMetricAsync(
         Func<short, CancellationToken, Task<FocasResult<IReadOnlyList<WireSpindleMetric>>>> call,
         CancellationToken cancellationToken)
     {
         var result = await call(-1, cancellationToken).ConfigureAwait(false);
         if (!result.IsOk || result.Value is null) return [];
-        var list = new List<int>();
-        foreach (var m in result.Value)
-        {
-            // Fanuc pads unused spindle slots with 0 — stop at the first trailing zero so the
-            // list length matches the configured spindle count.
-            if (m.Value == 0 && list.Count > 0) break;
-            list.Add(m.Value);
-        }
-        return list;
+        return result.Value.Select(m => m.Percent).ToList();
     }
 
     /// <summary>Disposes the wire client and releases all resources.</summary>
@@ -368,17 +367,14 @@ public sealed class WireFocasClient : IFocasClient
     }
 
     private async Task<(object? value, uint status)> ReadMacroAsync(
-        FocasAddress address, CancellationToken cancellationToken)
+        FocasAddress address, FocasDataType type, CancellationToken cancellationToken)
     {
         try
         {
             var result = await _wire.ReadMacroAsync((short)address.Number, cancellationToken).ConfigureAwait(false);
             if (!result.IsOk || result.Value is null)
                 return (null, FocasStatusMapper.MapFocasReturn(result.Rc));
-            var m = result.Value;
-            // Macro value is scaled-decimal: the real value is Value / 10^Decimal.
-            var scaled = m.Value / Math.Pow(10.0, m.Decimal);
-            return ((object)scaled, FocasStatusMapper.Good);
+            return MapMacro(result.Value, type, address.BitIndex);
         }
         catch (FocasWireException ex)
         {
@@ -386,6 +382,62 @@ public sealed class WireFocasClient : IFocasClient
         }
     }
 
+    /// <summary>
+    ///     Turn a decoded macro into the value + quality its tag publishes.
+    /// </summary>
+    /// <remarks>
+    ///     <para>A <b>vacant</b> variable has no value at all → <see cref="FocasStatusMapper.BadNoData"/>,
+    ///     never a Good <c>0</c> (its mantissa is 0, indistinguishable from a genuine zero).</para>
+    ///     <para>Float tags get <c>mantissa / 10^decimal</c>. <b>Integer</b> tags (Byte / Int16 /
+    ///     Int32 / Bit) get the exact whole value, tested with integer arithmetic
+    ///     (<c>mantissa % 10^decimal</c>) so no epsilon is involved; a fractional macro on an
+    ///     integer tag is <see cref="FocasStatusMapper.BadTypeMismatch"/> — truncating or rounding
+    ///     would publish a plausible wrong count at Good quality — and a whole value that does not
+    ///     fit the type is <see cref="FocasStatusMapper.BadOutOfRange"/>. Ported from the sister
+    ///     ignitionoee driver's <c>macroInteger</c>/<c>macroReal</c> (Focas-017/018).</para>
+    /// </remarks>
+    /// <param name="m">The decoded macro.</param>
+    /// <param name="type">The tag's declared data type.</param>
+    /// <param name="bitIndex">Optional bit index for a <see cref="FocasDataType.Bit"/> tag.</param>
+    /// <returns>The boxed value (null when Bad) and its status.</returns>
+    internal static (object? value, uint status) MapMacro(WireMacro m, FocasDataType type, int? bitIndex)
+    {
+        if (m.Scaled is not { } scaled) return (null, FocasStatusMapper.BadNoData);
+
+        switch (type)
+        {
+            case FocasDataType.Float64:
+                return (scaled, FocasStatusMapper.Good);
+            case FocasDataType.Float32:
+                return ((float)scaled, FocasStatusMapper.Good);
+            case FocasDataType.Byte or FocasDataType.Int16 or FocasDataType.Int32 or FocasDataType.Bit:
+                if (!TryWholeMacroValue(m, out var whole)) return (null, FocasStatusMapper.BadTypeMismatch);
+                return type switch
+                {
+                    FocasDataType.Bit => (bitIndex is int bit ? ((whole >> bit) & 1L) != 0 : whole != 0, FocasStatusMapper.Good),
+                    FocasDataType.Byte when whole is >= sbyte.MinValue and <= sbyte.MaxValue => ((sbyte)whole, FocasStatusMapper.Good),
+                    FocasDataType.Int16 when whole is >= short.MinValue and <= short.MaxValue => ((short)whole, FocasStatusMapper.Good),
+                    FocasDataType.Int32 when whole is >= int.MinValue and <= int.MaxValue => ((int)whole, FocasStatusMapper.Good),
+                    _ => (null, FocasStatusMapper.BadOutOfRange),
+                };
+            default:
+                return (scaled, FocasStatusMapper.Good);
+        }
+    }
+
+    /// <summary>Exact <c>mantissa / 10^decimal</c> when it is a whole number; integer arithmetic only.</summary>
+    private static bool TryWholeMacroValue(WireMacro m, out long whole)
+    {
+        whole = 0;
+        if (m.Value == 0) return true; // 0 is whole at any decimal
+        if (m.Decimal > 18) return false; // an i32 mantissa over 10^19+ is always fractional
+        var divisor = 1L;
+        for (var i = 0; i < m.Decimal; i++) divisor *= 10L;
+        if (m.Value % divisor != 0) return false;
+        whole = m.Value / divisor;
+        return true;
+    }
+
     private void RequireConnected()
     {
         if (!_wire.IsConnected)
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Docker/focas-mock/VENDORED.md b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Docker/focas-mock/VENDORED.md
index 701c4cc6..35907315 100644
--- a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Docker/focas-mock/VENDORED.md
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Docker/focas-mock/VENDORED.md
@@ -43,3 +43,18 @@ Copy-Item "$src\Dockerfile" "$dest\"
 Update the snapshot date at the top of this file afterward. No other
 files belong here — the Docker build context is just the Python package
 and its metadata.
+
+## Local divergence (do not lose on refresh)
+
+`src/focas_mock/server.py` and `defaults.py` carry OtOpcUa-local edits that make the wire
+shapes match a real FANUC 31i-B (Makino Z-34184) instead of shapes the driver and the mock had
+agreed on between themselves. A refresh that overwrites `src/` must re-apply them:
+
+- the little-endian `cnc_rdtimer` minute/msec encoding (2026-06-25, live-validated);
+- the alarm count cap on `cnc_rdalmmsg2`;
+- (2026-10-07, ported from the sister ignitionoee FOCAS mock) `0x00D3` ("cnc_getfigure", not a
+  real FOCAS wire command) refused with `EW_FUNC`; `0x0026` position blocks carrying their own
+  `base/exponent` (`position_figures` is now that exponent) and a signed `arg2`;
+  `cnc_rdmacro` as the 8-byte ODBM shape (`dec_val` at `[6..7]`, 9-digit mantissa, unset
+  macro = vacant); servo/spindle meter records with the `base/exponent` envelope, spindle
+  meters in 1/16384-of-full-scale counts.
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Docker/focas-mock/src/focas_mock/defaults.py b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Docker/focas-mock/src/focas_mock/defaults.py
index 45857ac1..4a2430d0 100644
--- a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Docker/focas-mock/src/focas_mock/defaults.py
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Docker/focas-mock/src/focas_mock/defaults.py
@@ -78,9 +78,12 @@ def make_default_state(profile: Mapping[str, Any]) -> dict[str, Any]:
         "acts": 3200,
         "acts2": [3200] + [0] * (max_spindles - 1),
         "axis_names": axis_names[:max_axis],
-        # Per-axis position decimal places served by cnc_getfigure (command 0x00d3).
-        # Default every configured axis to 0 ⇒ 10^0 = 1.0 scale, leaving existing
-        # position reads unchanged. mock_patch can override individual axes.
+        # Per-axis position scale, served INSIDE each cnc_rddynamic2 (0x0026) block as
+        # base 10 / this exponent — NOT by a separate command (0x00d3 "cnc_getfigure" was
+        # never real; the mock refuses it with EW_FUNC like the control does). Default 0 ⇒
+        # 10^0 = 1.0, leaving existing position reads unchanged. mock_patch can override an
+        # axis with an int exponent, or a dict {"base": .., "exponent": ..} — e.g.
+        # {"exponent": 65535} for the vacant marker.
         "position_figures": {name: 0 for name in axis_names[:max_axis]},
         "spindle_names": spindle_names,
         "parameters": {
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Docker/focas-mock/src/focas_mock/server.py b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Docker/focas-mock/src/focas_mock/server.py
index 827355ea..52e4ff05 100644
--- a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Docker/focas-mock/src/focas_mock/server.py
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Docker/focas-mock/src/focas_mock/server.py
@@ -7,6 +7,7 @@ from typing import Any, Awaitable, Callable
 
 from .constants import (
     ADMIN_METHODS,
+    EW_ATTRIB,
     EW_FUNC,
     EW_HANDLE,
     EW_NUMBER,
@@ -24,7 +25,52 @@ from .profiles import load_profile
 Handler = Callable[[dict[str, Any]], Awaitable[tuple[int, dict[str, Any] | None, str | None]]]
 
 
+class WireRefusal(Exception):
+    """One response block refuses with this FOCAS ``rc``.
+
+    Raised from a payload builder when the COMMAND exists but its ARGUMENTS name nothing the
+    control would answer (``cnc_rddynamic2`` with ``arg2 = 0``, for instance). Command-level
+    refusals live in ``FocasMockServer._WIRE_REFUSED_COMMANDS``. Ported from the sister
+    ignitionoee mock (Focas.Wire-020).
+    """
+
+    def __init__(self, rc: int) -> None:
+        super().__init__(f"refused with rc={rc}")
+        self.rc = rc
+
+
 class FocasMockServer:
+    # OtOpcUa-local changes to this vendored snapshot (2026-10-07), ported from the sister
+    # ignitionoee FOCAS mock so the wire shapes match a real FANUC 31i-B (Makino Z-34184) rather
+    # than shapes the driver and the mock once agreed on between themselves:
+    #   - 0x00D3 ("cnc_getfigure") is refused with EW_FUNC, as the real control does;
+    #   - 0x0026 position blocks carry their own base/exponent;
+    #   - cnc_rdmacro is the 8-byte ODBM shape with dec_val at [6..7];
+    #   - servo/spindle meter records carry the base/exponent envelope, spindle meters in
+    #     1/16384-of-full-scale counts.
+    # The little-endian cnc_rdtimer encoding and the alarm count cap stay as they were.
+
+    # cnc_rdmacro (ODBM) encoding constants — see _wire_rdmacro / _normalize_macro.
+    _MACRO_ODBM_LENGTH = 10
+    _MACRO_VACANT_DEC = -1
+    _MACRO_SIGNIFICANT_DIGITS = 9
+
+    # Commands this mock REFUSES, and with which rc — the real control's answer. 0x00D3 does not
+    # exist in the FOCAS wire protocol; serving it let a driver validate a command the real
+    # 31i-B refuses with rc=1.
+    _WIRE_REFUSED_COMMANDS = {0xD3: EW_FUNC}
+
+    # Default base served inside a 0x0026 position block (every block of the live 31i-B
+    # capture reports base 10).
+    _POSITION_DEFAULT_BASE = 10
+
+    # Servo/spindle meter records carry the same base/exponent envelope (live: base 10, exp 0).
+    _METER_BASE = 10
+
+    # SPINDLE meters (0x0040) are a fraction of full scale in 1/16384 units: 16384 = 100% of
+    # rated load (metric 0) or of maximum spindle speed (metric 1). SERVO meters are direct %.
+    _METER_FULL_SCALE = 16384
+
     def __init__(
         self,
         host: str,
@@ -208,10 +254,22 @@ class FocasMockServer:
 
     def _wire_response_block(self, request_block: bytes) -> bytes:
         command = int.from_bytes(request_block[6:8], "big") if len(request_block) >= 8 else 0
-        payload = self._wire_payload(command, request_block)
+        refused_rc = self._WIRE_REFUSED_COMMANDS.get(command)
+        if refused_rc is not None:
+            return self._make_wire_response_block(command, b"", request_block, rc=refused_rc)
+        try:
+            payload = self._wire_payload(command, request_block)
+        except WireRefusal as refusal:
+            return self._make_wire_response_block(command, b"", request_block, rc=refusal.rc)
         return self._make_wire_response_block(command, payload, request_block)
 
-    def _make_wire_response_block(self, command: int, payload: bytes, request_block: bytes | None = None) -> bytes:
+    def _make_wire_response_block(
+        self,
+        command: int,
+        payload: bytes,
+        request_block: bytes | None = None,
+        rc: int = EW_OK,
+    ) -> bytes:
         block_len = 0x10 + len(payload)
         block = bytearray(block_len)
         block[0:2] = block_len.to_bytes(2, "big")
@@ -219,6 +277,7 @@ class FocasMockServer:
             block[2:8] = request_block[2:8]
         else:
             block[6:8] = command.to_bytes(2, "big")
+        block[8:10] = int(rc).to_bytes(2, "big", signed=True)
         block[14:16] = len(payload).to_bytes(2, "big")
         block[16:] = payload
         return bytes(block)
@@ -256,8 +315,6 @@ class FocasMockServer:
             return self._wire_spindle_metric(request_block)
         if command == 0x56:
             return self._wire_servo_meter()
-        if command == 0xD3:
-            return self._wire_position_figures()
         if command == 0x57:
             mode = self.store.snapshot()["operation_mode"]
             return self._u16(int(mode.get("mode", 0) if isinstance(mode, dict) else mode))
@@ -322,23 +379,54 @@ class FocasMockServer:
         return self._u32(value)
 
     def _wire_dynamic_axis(self, request_block: bytes) -> bytes:
+        """Serves `cnc_rddynamic2` (0x0026) positions, honouring a SIGNED `arg2` the way the real
+        31i-B does (probed 2026-08-12 by the sister ignitionoee project, Focas.Wire-017/020):
+        `arg2 = 1..n` -> exactly one 8-byte block for that axis; `arg2 = -1` -> every slot in one
+        block; `arg2 = 0` or past the axis count -> refused (EW_ATTRIB)."""
         selector = self._block_u32(request_block, 8)
-        axis = self._block_u32(request_block, 12)
+        axis = self._block_i32(request_block, 12)
         field = {4: "absolute", 1: "machine", 6: "relative", 7: "distance"}.get(selector, "absolute")
         state = self.store.snapshot()
         names = list(state["axis_names"])
         dynamic_axes = state["dynamic"]["axes"]
+        if axis == 0 or axis > len(names):
+            raise WireRefusal(EW_ATTRIB)
+        if axis > 0:
+            name = names[axis - 1]
+            return self._wire_position_block(state, name, dynamic_axes.get(name, {}).get(field, 0))
         payload = bytearray()
         for name in names:
-            position = dynamic_axes.get(name, {})
-            payload += self._u32(int(position.get(field, 0)))
-            payload += self._u32(0)
-        if axis > 0 and axis <= len(names):
-            name = names[axis - 1]
-            position = dynamic_axes.get(name, {})
-            return self._u32(int(position.get(field, 0))) + self._u32(0)
+            payload += self._wire_position_block(state, name, dynamic_axes.get(name, {}).get(field, 0))
         return bytes(payload)
 
+    def _wire_position_block(self, state: dict[str, Any], name: str, raw: int) -> bytes:
+        """Encodes one 8-byte `cnc_rddynamic2` position block: value, then its OWN scale.
+
+            [0..3] i32 raw value
+            [4..5] u16 base      (2 or 10)
+            [6..7] u16 exponent  (0xFFFF = the slot holds no valid position)
+
+        `position_figures[name]` is the exponent (base 10); a dict value
+        `{"base": .., "exponent": ..}` overrides the base too, so a profile can serve a
+        deliberately undecodable block and prove the client Bads that one axis node.
+        """
+        base, exponent = self._position_scale(state, name)
+        return (
+            self._u32(int(raw))
+            + (base & 0xFFFF).to_bytes(2, "big")
+            + (exponent & 0xFFFF).to_bytes(2, "big")
+        )
+
+    def _position_scale(self, state: dict[str, Any], name: str) -> tuple[int, int]:
+        """Returns the (base, exponent) pair `position_figures` configures for one axis."""
+        configured = state.get("position_figures", {}).get(name, 0)
+        if isinstance(configured, dict):
+            return (
+                int(configured.get("base", self._POSITION_DEFAULT_BASE)),
+                int(configured.get("exponent", 0)),
+            )
+        return self._POSITION_DEFAULT_BASE, int(configured)
+
     def _wire_wrparam(self, request_block: bytes) -> None:
         datano = self._block_u32(request_block, 8)
         extra = request_block[28:]
@@ -346,11 +434,38 @@ class FocasMockServer:
         self.store.merge_patch({"parameters": {str(datano): {"type": "long", "value": value, "decimal": 0}}})
 
     def _wire_rdmacro(self, request_block: bytes) -> bytes:
+        """Encodes an ODBM `cnc_rdmacro` (0x0015) response payload, as a real 31i-B sends it
+        (golden capture `ref-macro-500-0x0015.bin`: `05 f5 e1 00 00 0a 00 08` = 1.0):
+
+            [0..3]  i32 mantissa (normalised to 9 significant digits)
+            [4..5]  i16 length field — a CONSTANT 10
+            [6..7]  i16 dec_val — decimal places; 0xFFFF (-1) = VACANT
+
+        A macro the profile does not mock is emitted as vacant, as a real control answers an
+        undefined variable.
+        """
         number = self._block_u32(request_block, 8)
-        macro = self.store.snapshot()["macros"].get(str(number), {})
-        value = int(macro.get("value", 0)) if isinstance(macro, dict) else 0
-        decimal = int(macro.get("decimal", 0)) if isinstance(macro, dict) else 0
-        return self._u32(value) + self._u16(decimal) + self._u16(0)
+        macro = self.store.snapshot()["macros"].get(str(number))
+        if isinstance(macro, dict):
+            mantissa, dec_val = self._normalize_macro(
+                int(macro.get("value", 0)), int(macro.get("decimal", 0))
+            )
+        else:
+            mantissa, dec_val = 0, self._MACRO_VACANT_DEC
+        return self._u32(mantissa) + self._u16(self._MACRO_ODBM_LENGTH) + self._u16(dec_val)
+
+    def _normalize_macro(self, value: int, decimal: int) -> tuple[int, int]:
+        """Turns a configured fixed-point `(value, decimal)` into the `(mantissa, dec_val)` a CNC
+        returns: the mantissa padded to 9 significant digits, `dec_val` raised to match
+        (live: `#502 = 270` -> `270000000/10^6`). The real value is unchanged."""
+        if decimal < 0:
+            return 0, self._MACRO_VACANT_DEC
+        if value == 0:
+            return 0, decimal
+        pad = self._MACRO_SIGNIFICANT_DIGITS - len(str(abs(value)))
+        if pad <= 0:
+            return value, decimal
+        return value * (10**pad), decimal + pad
 
     def _wire_wrmacro(self, request_block: bytes) -> None:
         number = self._block_u32(request_block, 8)
@@ -377,31 +492,34 @@ class FocasMockServer:
         payload = bytearray()
         for name in state["axis_names"]:
             entry = configured.get(name, {"name": name, "value": 0})
+            # 8-byte record (live 31i-B): value, then the base/exponent envelope. No axis name —
+            # the client pairs names positionally from the companion 0x0089 block.
             payload += self._u32(int(entry.get("value", 0)))
-            payload += self._u16(0)
-            payload += self._u16(1)
-            payload += self._name_record(name, 4)
-        return bytes(payload)
-
-    def _wire_position_figures(self) -> bytes:
-        state = self.store.snapshot()
-        figures = state.get("position_figures", {})
-        payload = bytearray()
-        for name in state["axis_names"]:
-            payload += self._u16(int(figures.get(name, 0)))
+            payload += self._u16(self._METER_BASE)
+            payload += self._u16(int(entry.get("exponent", 0)))
         return bytes(payload)
 
     def _wire_spindle_metric(self, request_block: bytes) -> bytes:
+        # Both metrics are 1/16384-of-full-scale COUNTS on the wire, not the human units the
+        # config holds. Metric 0: load % of rated (16384 = 100%). Metric 1: motor speed as a
+        # fraction of the spindle's maximum (`speed / max_rpm`) — NOT the maximum itself.
         metric = self._block_u32(request_block, 8)
         spindle = self.store.snapshot()["spindle"]
-        if metric == 1:
-            values = [int(value) for value in spindle.get("max_rpm", [])]
-        else:
-            values = [int(entry.get("load", 0)) for entry in spindle.get("load", [])]
+        maxima = [int(value) for value in spindle.get("max_rpm", [])]
+        entries = spindle.get("load", [])
+        values = []
+        for index, entry in enumerate(entries):
+            if metric == 1:
+                maximum = maxima[index] if index < len(maxima) else 0
+                speed = int(entry.get("speed", 0))
+                values.append(round(speed * self._METER_FULL_SCALE / maximum) if maximum else 0)
+            else:
+                values.append(round(int(entry.get("load", 0)) * self._METER_FULL_SCALE / 100))
         payload = bytearray()
         for value in values[:4]:
             payload += self._u32(value)
-            payload += self._u32(0)
+            payload += self._u16(self._METER_BASE)
+            payload += self._u16(0)
         return bytes(payload)
 
     def _wire_program_name(self) -> bytes:
@@ -480,6 +598,12 @@ class FocasMockServer:
             return 0
         return int.from_bytes(block[offset : offset + 4], "big")
 
+    def _block_i32(self, block: bytes, offset: int) -> int:
+        """A SIGNED request argument — `-1` is a real selector (all axes / all spindles)."""
+        if offset + 4 > len(block):
+            return 0
+        return int.from_bytes(block[offset : offset + 4], "big", signed=True)
+
     def _u16(self, value: int) -> bytes:
         return int(value).to_bytes(2, "big", signed=True)
 
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Series/WireBackendCoverageTests.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Series/WireBackendCoverageTests.cs
index f09d7e39..cc37571c 100644
--- a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Series/WireBackendCoverageTests.cs
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Series/WireBackendCoverageTests.cs
@@ -236,14 +236,15 @@ public sealed class WireBackendCoverageTests
     }
 
     /// <summary>
-    ///     Verifies that per-axis position figures fetched via <c>cnc_getfigure</c> (wire command
-    ///     0x00D3) scale the published <c>AbsolutePosition</c>, and that the auto figure wins over
-    ///     the configured <c>PositionDecimalPlaces</c> fallback knob.
-    ///     Seed: X axis absolute = 12345, figure = 3  →  published value = 12.345 (÷ 10^3).
-    ///     Config knob = 1  →  fallback would give 1234.5.  12.345 uniquely proves the wire path.
+    ///     Verifies that the scale carried INSIDE each <c>cnc_rddynamic2</c> position block
+    ///     (base 10 / exponent) scales the published <c>AbsolutePosition</c>, and that it wins over
+    ///     the configured <c>PositionDecimalPlaces</c> fallback knob. (The mock refuses the old
+    ///     <c>cnc_getfigure</c> 0x00D3 with EW_FUNC, as a real 31i-B does.)
+    ///     Seed: X axis absolute = 12345, exponent = 3  →  published value = 12.345 (÷ 10^3).
+    ///     Config knob = 1  →  fallback would give 1234.5.  12.345 uniquely proves the block scale.
     /// </summary>
     [Fact]
-    public async Task Position_figures_scale_axis_via_wire_backend()
+    public async Task Position_block_scale_scales_axis_via_wire_backend()
     {
         if (_fx.SkipReason is not null) Assert.Skip(_fx.SkipReason);
         var ct = TestContext.Current.CancellationToken;
@@ -261,13 +262,13 @@ public sealed class WireBackendCoverageTests
                     X = new { absolute = 12345, machine = 12345, relative = 0, distance = 0 },
                 },
             },
-            // Per-axis decimal-place figures for cnc_getfigure (command 0x00D3).
-            // The mock's _wire_position_figures() reads state["position_figures"][axisName].
+            // Per-axis exponent served inside each 0x0026 position block (base 10).
+            // The mock's _position_scale() reads state["position_figures"][axisName].
             position_figures = new { X = 3 },
         }, ct);
 
-        // PositionDecimalPlaces = 1 is intentionally different from the auto figure (3)
-        // so the assertion 12.345 uniquely proves the cnc_getfigure path won.
+        // PositionDecimalPlaces = 1 is intentionally different from the block exponent (3)
+        // so the assertion 12.345 uniquely proves the block's own scale won.
         var driver = new FocasDriver(new FocasDriverOptions
         {
             Devices = [new FocasDeviceOptions(DeviceHost, PositionDecimalPlaces: 1)],
@@ -295,13 +296,90 @@ public sealed class WireBackendCoverageTests
             state.ShouldNotBeNull();
             var published = state.LastFixedSnapshots[$"{DeviceHost}/Axes/X/AbsolutePosition"];
 
-            // 12345 ÷ 10^3 = 12.345  →  auto figure (3) won.
+            // 12345 ÷ 10^3 = 12.345  →  the block's own scale (3) won.
             // 12345 ÷ 10^1 = 1234.5  →  would mean config knob (1) was used instead.
             // 12345 ÷ 10^0 = 12345.0 →  would mean no scaling at all.
             published.ShouldBe(12.345, tolerance: 0.0001);
         }
     }
 
+    /// <summary>
+    ///     "The control described no value" reads Bad over the real wire, never a Good number:
+    ///     a vacant <c>0x0026</c> position block (exponent <c>0xFFFF</c>) Bads only its own axis
+    ///     node, an unset macro (vacant <c>dec_val</c>) Bads its tag, and a fractional macro on an
+    ///     integer tag is refused rather than truncated — while a normalised 9-digit macro
+    ///     mantissa de-scales to its real value.
+    /// </summary>
+    [Fact]
+    public async Task Vacant_positions_and_macros_read_bad_over_the_wire()
+    {
+        if (_fx.SkipReason is not null) Assert.Skip(_fx.SkipReason);
+        var ct = TestContext.Current.CancellationToken;
+
+        await _fx.LoadProfileAsync("FWLIB64", ct);
+        await _fx.PatchStateAsync(new
+        {
+            axis_names = new[] { "X", "Y" },
+            dynamic = new
+            {
+                alarm = 0, prgnum = 1, prgmnum = 1, seqnum = 1, actf = 0, acts = 0,
+                axes = new
+                {
+                    X = new { absolute = 1, machine = 1, relative = 0, distance = 0 },
+                    Y = new { absolute = 370177, machine = 370177, relative = 0, distance = 0 },
+                },
+            },
+            position_figures = new Dictionary<string, object>
+            {
+                ["X"] = new { exponent = 0xFFFF },   // vacant-slot marker
+                ["Y"] = 3,
+            },
+            macros = new Dictionary<string, object>
+            {
+                ["502"] = new { value = 270, @decimal = 0 },     // served as 270000000 / 10^6
+                ["508"] = new { value = 1485, @decimal = 1 },    // 148.5
+            },
+        }, ct);
+
+        var drv = new FocasDriver(new FocasDriverOptions
+        {
+            Devices = [new FocasDeviceOptions(DeviceHost)],
+            RawTags = FocasRawTags.Entries(
+                new FocasTagDefinition("Count502", DeviceHost, "MACRO:502", FocasDataType.Int32, Writable: false),
+                new FocasTagDefinition("Frac508",  DeviceHost, "MACRO:508", FocasDataType.Int32, Writable: false),
+                new FocasTagDefinition("Unset611", DeviceHost, "MACRO:611", FocasDataType.Float64, Writable: false)),
+            Probe = new FocasProbeOptions { Enabled = false },
+            FixedTree = new FocasFixedTreeOptions
+            {
+                Enabled = true,
+                PollInterval = TimeSpan.FromMilliseconds(100),
+                ProgramPollInterval = TimeSpan.Zero,
+                TimerPollInterval = TimeSpan.Zero,
+            },
+        }, driverInstanceId: "wire-vacant", clientFactory: new WireFocasClientFactory());
+
+        await using (drv)
+        {
+            await drv.InitializeAsync("{}", ct);
+            await WaitFor(() =>
+                drv.GetDeviceState(DeviceHost)?.LastFixedSnapshots
+                    .ContainsKey($"{DeviceHost}/Axes/Y/AbsolutePosition") == true,
+                TimeSpan.FromSeconds(5));
+
+            var snaps = await drv.ReadAsync(
+                [$"{DeviceHost}/Axes/X/AbsolutePosition", $"{DeviceHost}/Axes/Y/AbsolutePosition",
+                 "Count502", "Frac508", "Unset611"], ct);
+
+            snaps[0].StatusCode.ShouldBe(FocasStatusMapper.BadNoData);
+            snaps[1].StatusCode.ShouldBe(FocasStatusMapper.Good);
+            Convert.ToDouble(snaps[1].Value).ShouldBe(370.177, tolerance: 1e-9);
+            snaps[2].StatusCode.ShouldBe(FocasStatusMapper.Good);
+            snaps[2].Value.ShouldBe(270);
+            snaps[3].StatusCode.ShouldBe(FocasStatusMapper.BadTypeMismatch);
+            snaps[4].StatusCode.ShouldBe(FocasStatusMapper.BadNoData);
+        }
+    }
+
     private static async Task WaitFor(Func<bool> pred, TimeSpan timeout)
     {
         var deadline = DateTime.UtcNow + timeout;
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Series/WireBackendTests.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Series/WireBackendTests.cs
index 6eff4b42..19ef82d0 100644
--- a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Series/WireBackendTests.cs
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.IntegrationTests/Series/WireBackendTests.cs
@@ -210,9 +210,13 @@ public sealed class WireBackendTests
         }
     }
 
-    /// <summary>Verifies that spindle load and max RPM data populate via the wire backend.</summary>
+    /// <summary>
+    ///     Verifies that the spindle load and motor-speed meters populate via the wire backend as
+    ///     percentages of full scale (the mock serves 1/16384-of-full-scale counts, as a real
+    ///     31i-B does): S1 load 56% / speed 3200 of 6000 rpm = 53.3%, S2 load 12% / 1800 of 4500 = 40%.
+    /// </summary>
     [Fact]
-    public async Task Spindle_load_and_max_rpm_populate_via_wire_backend()
+    public async Task Spindle_load_and_motor_speed_populate_via_wire_backend()
     {
         if (_fx.SkipReason is not null) Assert.Skip(_fx.SkipReason);
         var ct = TestContext.Current.CancellationToken;
@@ -260,21 +264,21 @@ public sealed class WireBackendTests
             await WaitFor(() =>
             {
                 var state = driver.GetDeviceState(DeviceHost);
-                return state?.FixedTreeCache is { Capabilities.SpindleLoad: true, Capabilities.SpindleMaxRpm: true }
+                return state?.FixedTreeCache is { Capabilities.SpindleLoad: true, Capabilities.SpindleMotorSpeed: true }
                     && state.LastSpindleLoads.Count >= 2;
             }, TimeSpan.FromSeconds(5));
 
             var snapshots = await driver.ReadAsync(
                 [$"{DeviceHost}/Spindle/S1/Load",
-                 $"{DeviceHost}/Spindle/S1/MaxRpm",
+                 $"{DeviceHost}/Spindle/S1/MotorSpeedPct",
                  $"{DeviceHost}/Spindle/S2/Load",
-                 $"{DeviceHost}/Spindle/S2/MaxRpm"], ct);
+                 $"{DeviceHost}/Spindle/S2/MotorSpeedPct"], ct);
 
             snapshots.ShouldAllBe(s => s.StatusCode == FocasStatusMapper.Good);
-            Convert.ToInt32(snapshots[0].Value).ShouldBe(56);
-            Convert.ToInt32(snapshots[1].Value).ShouldBe(6000);
-            Convert.ToInt32(snapshots[2].Value).ShouldBe(12);
-            Convert.ToInt32(snapshots[3].Value).ShouldBe(4500);
+            Convert.ToDouble(snapshots[0].Value).ShouldBe(56.0, tolerance: 0.01);
+            Convert.ToDouble(snapshots[1].Value).ShouldBe(3200 * 100.0 / 6000, tolerance: 0.01);
+            Convert.ToDouble(snapshots[2].Value).ShouldBe(12.0, tolerance: 0.01);
+            Convert.ToDouble(snapshots[3].Value).ShouldBe(40.0, tolerance: 0.01);
         }
     }
 
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FakeFocasClient.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FakeFocasClient.cs
index a488df99..ce8671e6 100644
--- a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FakeFocasClient.cs
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FakeFocasClient.cs
@@ -140,25 +140,18 @@ internal class FakeFocasClient : IFocasClient
     public virtual Task<IReadOnlyList<FocasServoLoad>> GetServoLoadsAsync(CancellationToken ct) =>
         Task.FromResult<IReadOnlyList<FocasServoLoad>>([.. ServoLoads]);
 
-    /// <summary>Gets the list of spindle loads.</summary>
-    public List<int> SpindleLoads { get; } = [];
-    /// <summary>Gets the list of spindle maximum RPMs.</summary>
-    public List<int> SpindleMaxRpms { get; } = [];
+    /// <summary>Gets the list of spindle load percentages (null = undescribable slot).</summary>
+    public List<double?> SpindleLoads { get; } = [];
+    /// <summary>Gets the list of spindle motor-speed percentages (null = undescribable slot).</summary>
+    public List<double?> SpindleMotorSpeeds { get; } = [];
     /// <summary>Gets spindle loads asynchronously.</summary>
     /// <param name="ct">The cancellation token.</param>
-    public virtual Task<IReadOnlyList<int>> GetSpindleLoadsAsync(CancellationToken ct) =>
-        Task.FromResult<IReadOnlyList<int>>([.. SpindleLoads]);
-    /// <summary>Gets spindle maximum RPMs asynchronously.</summary>
+    public virtual Task<IReadOnlyList<double?>> GetSpindleLoadsAsync(CancellationToken ct) =>
+        Task.FromResult<IReadOnlyList<double?>>([.. SpindleLoads]);
+    /// <summary>Gets spindle motor-speed percentages asynchronously.</summary>
     /// <param name="ct">The cancellation token.</param>
-    public virtual Task<IReadOnlyList<int>> GetSpindleMaxRpmsAsync(CancellationToken ct) =>
-        Task.FromResult<IReadOnlyList<int>>([.. SpindleMaxRpms]);
-
-    /// <summary>Gets or sets the per-axis position decimal-place figures returned by <see cref="GetPositionFiguresAsync"/>.</summary>
-    public IReadOnlyList<int> PositionFigures { get; set; } = [];
-    /// <summary>Gets the per-axis position decimal-place figures asynchronously.</summary>
-    /// <param name="ct">The cancellation token.</param>
-    public virtual Task<IReadOnlyList<int>> GetPositionFiguresAsync(CancellationToken ct) =>
-        Task.FromResult(PositionFigures);
+    public virtual Task<IReadOnlyList<double?>> GetSpindleMotorSpeedsAsync(CancellationToken ct) =>
+        Task.FromResult<IReadOnlyList<double?>>([.. SpindleMotorSpeeds]);
 
     /// <summary>Disposes the client.</summary>
     public virtual void Dispose()
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/Fixtures/v3/live-dynamic2-axis1-0x0026.bin b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/Fixtures/v3/live-dynamic2-axis1-0x0026.bin
new file mode 100644
index 00000000..7f51296a
Binary files /dev/null and b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/Fixtures/v3/live-dynamic2-axis1-0x0026.bin differ
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/Fixtures/v3/live-dynamic2-axis2-0x0026.bin b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/Fixtures/v3/live-dynamic2-axis2-0x0026.bin
new file mode 100644
index 00000000..cc7308a8
Binary files /dev/null and b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/Fixtures/v3/live-dynamic2-axis2-0x0026.bin differ
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/Fixtures/v3/live-spmeter-load-0x0040.bin b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/Fixtures/v3/live-spmeter-load-0x0040.bin
new file mode 100644
index 00000000..3d98bc57
Binary files /dev/null and b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/Fixtures/v3/live-spmeter-load-0x0040.bin differ
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/Fixtures/v3/live-spmeter-maxrpm-0x0040.bin b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/Fixtures/v3/live-spmeter-maxrpm-0x0040.bin
new file mode 100644
index 00000000..3a4a2415
Binary files /dev/null and b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/Fixtures/v3/live-spmeter-maxrpm-0x0040.bin differ
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasDuplicateSiblingNameTests.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasDuplicateSiblingNameTests.cs
index 87bc65f4..a2d1c33b 100644
--- a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasDuplicateSiblingNameTests.cs
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasDuplicateSiblingNameTests.cs
@@ -34,8 +34,8 @@ public sealed class FocasDuplicateSiblingNameTests
             // Two spindles whose displays also collide, with distinct data per slot.
             c.SpindleNames.Clear();
             c.SpindleNames.AddRange([new("S", "1", "", ""), new("S", "1", "", "")]);
-            c.SpindleLoads.AddRange([5, 7]);
-            c.SpindleMaxRpms.AddRange([8_000, 12_000]);
+            c.SpindleLoads.AddRange([5.0, 7.0]);
+            c.SpindleMotorSpeeds.AddRange([40.0, 60.0]);
             return c;
         },
     };
@@ -159,17 +159,17 @@ public sealed class FocasDuplicateSiblingNameTests
         // The spindle read path matched by display name and took the FIRST index that matched,
         // so a duplicate spindle name made the second spindle's data unreachable.
         var drv = await StartedDriverAsync(
-            new FocasTagDefinition("raw/s1load", Host, "FIXED:Spindle/S1_1/Load", FocasDataType.Int32, Writable: false),
-            new FocasTagDefinition("raw/s2load", Host, "FIXED:Spindle/S1_2/Load", FocasDataType.Int32, Writable: false),
-            new FocasTagDefinition("raw/s1max", Host, "FIXED:Spindle/S1_1/MaxRpm", FocasDataType.Int32, Writable: false),
-            new FocasTagDefinition("raw/s2max", Host, "FIXED:Spindle/S1_2/MaxRpm", FocasDataType.Int32, Writable: false));
+            new FocasTagDefinition("raw/s1load", Host, "FIXED:Spindle/S1_1/Load", FocasDataType.Float64, Writable: false),
+            new FocasTagDefinition("raw/s2load", Host, "FIXED:Spindle/S1_2/Load", FocasDataType.Float64, Writable: false),
+            new FocasTagDefinition("raw/s1speed", Host, "FIXED:Spindle/S1_1/MotorSpeedPct", FocasDataType.Float64, Writable: false),
+            new FocasTagDefinition("raw/s2speed", Host, "FIXED:Spindle/S1_2/MotorSpeedPct", FocasDataType.Float64, Writable: false));
 
-        var read = await drv.ReadAsync(["raw/s1load", "raw/s2load", "raw/s1max", "raw/s2max"], CancellationToken.None);
+        var read = await drv.ReadAsync(["raw/s1load", "raw/s2load", "raw/s1speed", "raw/s2speed"], CancellationToken.None);
 
-        read[0].Value.ShouldBe(5);
-        read[1].Value.ShouldBe(7);
-        read[2].Value.ShouldBe(8_000);
-        read[3].Value.ShouldBe(12_000);
+        read[0].Value.ShouldBe(5.0);
+        read[1].Value.ShouldBe(7.0);
+        read[2].Value.ShouldBe(40.0);
+        read[3].Value.ShouldBe(60.0);
         read.ShouldAllBe(r => r.StatusCode == FocasStatusMapper.Good);
 
         await drv.ShutdownAsync(CancellationToken.None);
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasMacroDecodeTests.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasMacroDecodeTests.cs
new file mode 100644
index 00000000..15bcdaab
--- /dev/null
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasMacroDecodeTests.cs
@@ -0,0 +1,143 @@
+using System.Buffers.Binary;
+using Shouldly;
+using Xunit;
+using ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Wire;
+
+namespace ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests;
+
+/// <summary>
+///     <c>cnc_rdmacro</c> (0x0015) decode, pinned to real FANUC 31i-B payloads. Ported from the
+///     sister ignitionoee FOCAS driver's v0.15.0 fix (review finding Focas.Wire-013 / Focas-017).
+/// </summary>
+/// <remarks>
+///     The on-wire <c>ODBM</c> payload is 8 bytes: <c>[0..3] i32 mantissa</c>,
+///     <c>[4..5] i16</c> — a <b>constant 10</b> on every observed response (a length field, NOT the
+///     decimal), and <c>[6..7] i16 dec_val</c> (<c>0xFFFF</c> = vacant). Reading the decimal at
+///     offset 4 decodes every macro on every control without ever failing — just wrongly: the
+///     captured <c>#500 = 1.0</c> (<c>05 f5 e1 00 00 0a 00 08</c>) read as <c>100000000 / 10^10 =
+///     0.01</c>. FANUC normalises a macro to a 9-significant-digit mantissa, so the live vectors
+///     below (Makino Z-34184, 2026-08-05) all carry large mantissas.
+/// </remarks>
+[Trait("Category", "Unit")]
+public sealed class FocasMacroDecodeTests
+{
+    private static byte[] Odbm(int mantissa, int decVal, int lengthField = 10)
+    {
+        var p = new byte[8];
+        BinaryPrimitives.WriteInt32BigEndian(p.AsSpan(0, 4), mantissa);
+        BinaryPrimitives.WriteUInt16BigEndian(p.AsSpan(4, 2), (ushort)lengthField);
+        BinaryPrimitives.WriteUInt16BigEndian(p.AsSpan(6, 2), (ushort)(decVal & 0xFFFF));
+        return p;
+    }
+
+    [Fact]
+    public void ParseMacro_decodes_the_live_capture_with_the_decimal_at_offset_6()
+    {
+        var payload = WireFixtures.Payload("ref-macro-500-0x0015.bin", 0x0015);
+
+        var m = FocasWireClient.ParseMacro(500, payload);
+
+        m.Number.ShouldBe((short)500);
+        m.Value.ShouldBe(100_000_000);
+        m.Decimal.ShouldBe((short)8);   // offset 6 — NOT the constant 10 at offset 4
+        m.IsVacant.ShouldBeFalse();
+        m.Scaled!.Value.ShouldBe(1.0, 1e-12);
+    }
+
+    [Fact]
+    public void ParseMacro_ignores_the_length_field_at_offset_4()
+    {
+        var a = FocasWireClient.ParseMacro(508, Odbm(148_500_000, 6));
+        var b = FocasWireClient.ParseMacro(508, Odbm(148_500_000, 6, lengthField: 0));
+
+        b.ShouldBe(a);
+        b.Scaled!.Value.ShouldBe(148.5, 1e-9);
+    }
+
+    [Theory]
+    [InlineData(270_000_000, 6, 270.0)]          // #502
+    [InlineData(148_500_000, 6, 148.5)]          // #508
+    [InlineData(208_850_000, 4, 20885.0)]        // #610
+    [InlineData(202_608_050, 1, 20_260_805.0)]   // #3011 date
+    [InlineData(-100_000_000, 12, -1.0e-4)]      // #802
+    [InlineData(969_479_000, 9, 0.969479)]       // #801
+    [InlineData(1234, 0, 1234.0)]
+    public void ParseMacro_scales_the_live_vectors(int mantissa, int dec, double expected)
+    {
+        FocasWireClient.ParseMacro(1, Odbm(mantissa, dec)).Scaled!.Value.ShouldBe(expected, 1e-9);
+    }
+
+    [Fact]
+    public void A_vacant_macro_has_no_value_not_zero()
+    {
+        var m = FocasWireClient.ParseMacro(611, Odbm(0, 0xFFFF));
+
+        m.Decimal.ShouldBe((short)-1);
+        m.IsVacant.ShouldBeTrue();
+        m.Scaled.ShouldBeNull();
+    }
+
+    [Fact]
+    public void A_genuine_zero_is_not_vacant()
+    {
+        var m = FocasWireClient.ParseMacro(3901, Odbm(0, 0));
+        m.IsVacant.ShouldBeFalse();
+        m.Scaled.ShouldBe(0.0);
+    }
+
+    [Theory]
+    [InlineData(0)]
+    [InlineData(4)]
+    [InlineData(6)]
+    [InlineData(7)]
+    public void ParseMacro_refuses_a_payload_too_short_to_carry_dec_val(int length)
+    {
+        Should.Throw<FocasWireException>(() => FocasWireClient.ParseMacro(1, new byte[length]));
+    }
+
+    // ---- published value / quality ----
+
+    [Fact]
+    public void Float64_publishes_the_scaled_value_good()
+    {
+        var (value, status) = WireFocasClient.MapMacro(FocasWireClient.ParseMacro(508, Odbm(148_500_000, 6)), FocasDataType.Float64, null);
+        status.ShouldBe(FocasStatusMapper.Good);
+        value.ShouldBe(148.5);
+    }
+
+    [Fact]
+    public void Int32_publishes_the_exact_whole_value_not_the_mantissa()
+    {
+        var (value, status) = WireFocasClient.MapMacro(FocasWireClient.ParseMacro(502, Odbm(270_000_000, 6)), FocasDataType.Int32, null);
+        status.ShouldBe(FocasStatusMapper.Good);
+        value.ShouldBe(270);
+    }
+
+    [Fact]
+    public void A_fractional_macro_on_an_integer_tag_is_bad_not_truncated()
+    {
+        var (value, status) = WireFocasClient.MapMacro(FocasWireClient.ParseMacro(508, Odbm(148_500_000, 6)), FocasDataType.Int32, null);
+        status.ShouldBe(FocasStatusMapper.BadTypeMismatch);
+        value.ShouldBeNull();
+    }
+
+    [Theory]
+    [InlineData(FocasDataType.Float64)]
+    [InlineData(FocasDataType.Float32)]
+    [InlineData(FocasDataType.Int32)]
+    public void A_vacant_macro_is_bad_for_every_type(FocasDataType type)
+    {
+        var (value, status) = WireFocasClient.MapMacro(FocasWireClient.ParseMacro(611, Odbm(0, 0xFFFF)), type, null);
+        status.ShouldBe(FocasStatusMapper.BadNoData);
+        value.ShouldBeNull();
+    }
+
+    [Fact]
+    public void A_whole_macro_out_of_range_for_its_integer_type_is_bad()
+    {
+        // 70000 is whole, but does not fit Int16.
+        var (value, status) = WireFocasClient.MapMacro(FocasWireClient.ParseMacro(1, Odbm(700_000_000, 4)), FocasDataType.Int16, null);
+        status.ShouldBe(FocasStatusMapper.BadOutOfRange);
+        value.ShouldBeNull();
+    }
+}
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasMeterDecodeTests.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasMeterDecodeTests.cs
new file mode 100644
index 00000000..ef0cd867
--- /dev/null
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasMeterDecodeTests.cs
@@ -0,0 +1,127 @@
+using System.Buffers.Binary;
+using Shouldly;
+using Xunit;
+using ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Wire;
+
+namespace ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests;
+
+/// <summary>
+///     Servo (<c>cnc_rdsvmeter</c>, 0x0056) and spindle (<c>cnc_rdspmeter</c>, 0x0040) meter decode.
+///     Both are arrays of 8-byte records carrying the same self-describing envelope as every other
+///     value block on this wire — <c>[+0..3] i32 value</c>, <c>[+4..5] u16 base</c> (2 or 10),
+///     <c>[+6..7] u16 exponent</c> — so <c>scaled = value / base^exponent</c>.
+///     Ported from the sister ignitionoee FOCAS driver v0.17.2 / v0.17.3 (Focas.Wire-019).
+/// </summary>
+/// <remarks>
+///     <para><b>Servo: offset 4 is the BASE, not a decimal count.</b> It holds a steady 10, so the
+///     old <c>value / 10^decimal</c> divided every load by 10^10 and published ~0 — on a real
+///     Makino cutting at 20,000 rpm the panel read servo 0% on every axis. Servo meters are
+///     <b>direct</b> percentages (the live capture shows −57..227).</para>
+///     <para><b>Spindle: a fraction of full scale in 1/16384 units.</b> Settled on the real Z-34184
+///     by regressing the type-1 meter against the independently read <c>cnc_rddynamic2</c> spindle
+///     speed over 596–20,000 rpm: <c>rpm = 1.220749 × meter</c>, and <c>16384 × 1.220749 =
+///     20000.75</c> — full scale is the spindle's 20,000 rpm maximum. So the type-1 meter
+///     (<c>cnc_rdspmaxrpm</c> by name) is the <b>motor speed as a % of maximum</b>, not a max-rpm
+///     constant; the type-0 load meter shares the envelope and the 16384 = 100% scale (its
+///     acceleration peaks pin at 32767 — one count short of a 200% overload).</para>
+/// </remarks>
+[Trait("Category", "Unit")]
+public sealed class FocasMeterDecodeTests
+{
+    private static byte[] Record(int value, int @base, int exponent)
+    {
+        var b = new byte[8];
+        BinaryPrimitives.WriteInt32BigEndian(b.AsSpan(0, 4), value);
+        BinaryPrimitives.WriteUInt16BigEndian(b.AsSpan(4, 2), (ushort)@base);
+        BinaryPrimitives.WriteUInt16BigEndian(b.AsSpan(6, 2), (ushort)exponent);
+        return b;
+    }
+
+    // ---- servo ----
+
+    [Fact]
+    public void The_live_servo_capture_reads_direct_percentages_not_value_over_ten_to_the_tenth()
+    {
+        var blocks = WireFixtures.Blocks("svmeter-pair-0x0056-0x0089.bin");
+        var meters = FocasWireClient.ParseServoMeters(
+            blocks.First(b => b.Command == 0x0056).Payload,
+            blocks.First(b => b.Command == 0x0089).Payload,
+            maxCount: 32);
+
+        meters[0].Base.ShouldBe(10);
+        meters[0].Exponent.ShouldBe(0);
+        meters.Take(3).Select(m => m.Scaled).ShouldBe([0.0, 50.0, -3.0]);
+    }
+
+    [Fact]
+    public void A_servo_record_applies_its_own_exponent()
+    {
+        var m = FocasWireClient.ParseServoMeters(Record(1234, 10, 1), Array.Empty<byte>(), 32).Single();
+        m.Scaled!.Value.ShouldBe(123.4, 1e-9);
+    }
+
+    [Theory]
+    [InlineData(5, 7, 0)]        // base neither 2 nor 10
+    [InlineData(5, 10, 2560)]    // residue past the controlled-axis count
+    public void An_undescribable_servo_record_has_no_value_not_zero(int value, int @base, int exponent)
+    {
+        var m = FocasWireClient.ParseServoMeters(Record(value, @base, exponent), Array.Empty<byte>(), 32).Single();
+        m.IsValid.ShouldBeFalse();
+        m.Scaled.ShouldBeNull();
+    }
+
+    // ---- spindle ----
+
+    [Fact]
+    public void The_live_spindle_load_capture_is_a_percentage_of_16384()
+    {
+        var metrics = FocasWireClient.ParseSpindleMetrics(
+            WireFixtures.Payload("live-spmeter-load-0x0040.bin", 0x0040));
+
+        // Slot 1: raw 0x23C3 = 9155, base 10, exponent 0 → 9155 × 100 / 16384 ≈ 55.88 %.
+        metrics[0].Value.ShouldBe(9155);
+        metrics[0].Percent!.Value.ShouldBe(9155 * 100.0 / 16384, 1e-9);
+        // Slot 2 is buffer residue (exponent 0x0A00 = 2560): no value, not a number.
+        metrics[1].IsValid.ShouldBeFalse();
+        metrics[1].Percent.ShouldBeNull();
+    }
+
+    [Fact]
+    public void The_live_motor_speed_capture_is_a_percentage_of_maximum_speed()
+    {
+        var metrics = FocasWireClient.ParseSpindleMetrics(
+            WireFixtures.Payload("live-spmeter-maxrpm-0x0040.bin", 0x0040));
+
+        // 0x3FFD = 16381 ≈ 99.98 % — a spindle at (just under) its 20,000 rpm maximum.
+        metrics[0].Value.ShouldBe(16381);
+        metrics[0].Percent!.Value.ShouldBe(16381 * 100.0 / 16384, 1e-9);
+    }
+
+    [Theory]
+    [InlineData(16382, 19998)]
+    [InlineData(12286, 14998)]
+    [InlineData(9830, 12000)]
+    [InlineData(695, 850)]
+    [InlineData(488, 595)]
+    public void Percent_reproduces_the_live_motor_speed_regression(int meter, int rpm)
+    {
+        var m = FocasWireClient.ParseSpindleMetrics(Record(meter, 10, 0)).Single();
+        m.Percent!.Value.ShouldBe(rpm * 100.0 / 20000.0, 0.02);
+    }
+
+    [Fact]
+    public void Full_scale_is_16384_and_overload_is_not_clamped()
+    {
+        WireSpindleMetric.FullScale.ShouldBe(16384);
+        FocasWireClient.ParseSpindleMetrics(Record(16384, 10, 0)).Single().Percent.ShouldBe(100.0);
+        var overload = FocasWireClient.ParseSpindleMetrics(Record(32767, 10, 0)).Single().Percent!.Value;
+        overload.ShouldBeInRange(199.9, 200.0);
+    }
+
+    [Fact]
+    public void The_spindle_envelope_exponent_applies_before_the_full_scale_division()
+    {
+        // 163840 / 10^1 = 16384 counts = 100 %.
+        FocasWireClient.ParseSpindleMetrics(Record(163840, 10, 1)).Single().Percent!.Value.ShouldBe(100.0, 1e-9);
+    }
+}
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasMeterPublishTests.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasMeterPublishTests.cs
new file mode 100644
index 00000000..3294aa8f
--- /dev/null
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasMeterPublishTests.cs
@@ -0,0 +1,134 @@
+using Shouldly;
+using Xunit;
+using ZB.MOM.WW.OtOpcUa.Core.Abstractions;
+using ZB.MOM.WW.OtOpcUa.Driver.FOCAS;
+
+namespace ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests;
+
+/// <summary>
+///     Driver-level publish of servo / spindle meters (Focas.Wire-019 port): percentages publish
+///     Good as Float64, an undescribable record publishes BadNoData (never a Good 0), and the
+///     spindle motor-speed meter is a live, polled <c>MotorSpeedPct</c> — not the bootstrap-time
+///     <c>MaxRpm</c> constant it was mislabelled as.
+/// </summary>
+[Trait("Category", "Unit")]
+public sealed class FocasMeterPublishTests
+{
+    private const string Host = "focas://10.0.0.5:8193";
+
+    private static FocasDriver NewDriver(FakeFocasClient client) =>
+        new(new FocasDriverOptions
+        {
+            Devices = [new FocasDeviceOptions(Host)],
+            Probe = new FocasProbeOptions { Enabled = false },
+            FixedTree = new FocasFixedTreeOptions { Enabled = true, PollInterval = TimeSpan.FromMilliseconds(10) },
+        }, "drv-1", new FakeFocasClientFactory { Customise = () => client });
+
+    private static async Task<DataValueSnapshot> ReadSettledAsync(FocasDriver drv, string reference, Func<DataValueSnapshot, bool> settled)
+    {
+        var deadline = DateTime.UtcNow + TimeSpan.FromSeconds(5);
+        DataValueSnapshot last;
+        do
+        {
+            last = (await drv.ReadAsync([reference], CancellationToken.None)).Single();
+            if (settled(last)) return last;
+            await Task.Delay(15);
+        } while (DateTime.UtcNow < deadline);
+        return last;
+    }
+
+    private static FakeFocasClient MachineClient()
+    {
+        var c = new FakeFocasClient();
+        c.AxisNames.Clear();
+        c.AxisNames.AddRange([new("X", ""), new("Y", "")]);
+        c.ServoLoads.AddRange([new("X", 46.0), new("Y", null)]); // Y: undescribable record
+        c.SpindleNames.Clear();
+        c.SpindleNames.Add(new("S", "1", "", ""));
+        c.SpindleLoads.Add(55.88);
+        c.SpindleMotorSpeeds.Add(2.49);
+        return c;
+    }
+
+    [Fact]
+    public async Task Servo_loads_publish_percentages_and_an_undescribable_record_is_bad()
+    {
+        var drv = NewDriver(MachineClient());
+        await drv.InitializeAsync("{}", CancellationToken.None);
+
+        var x = await ReadSettledAsync(drv, $"{Host}/Axes/X/ServoLoad", s => s.StatusCode == FocasStatusMapper.Good);
+        var y = await ReadSettledAsync(drv, $"{Host}/Axes/Y/ServoLoad", s => s.StatusCode == FocasStatusMapper.BadNoData);
+
+        x.Value.ShouldBe(46.0);
+        y.StatusCode.ShouldBe(FocasStatusMapper.BadNoData);
+        y.Value.ShouldBeNull();
+        await drv.ShutdownAsync(CancellationToken.None);
+    }
+
+    [Fact]
+    public async Task Spindle_meters_publish_float64_percentages_and_motor_speed_is_polled_live()
+    {
+        var client = MachineClient();
+        var drv = NewDriver(client);
+        await drv.InitializeAsync("{}", CancellationToken.None);
+
+        var load = await ReadSettledAsync(drv, $"{Host}/Spindle/S1/Load", s => s.StatusCode == FocasStatusMapper.Good);
+        load.Value.ShouldBe(55.88);
+        (await ReadSettledAsync(drv, $"{Host}/Spindle/S1/MotorSpeedPct", s => s.StatusCode == FocasStatusMapper.Good))
+            .Value.ShouldBe(2.49);
+
+        // The spindle speeds up: the poll loop must follow it (MaxRpm was read once at bootstrap).
+        client.SpindleMotorSpeeds[0] = 99.98;
+        (await ReadSettledAsync(drv, $"{Host}/Spindle/S1/MotorSpeedPct", s => Equals(s.Value, 99.98)))
+            .Value.ShouldBe(99.98);
+        await drv.ShutdownAsync(CancellationToken.None);
+    }
+
+    [Fact]
+    public async Task An_undescribable_spindle_slot_is_bad_not_zero()
+    {
+        var client = MachineClient();
+        client.SpindleLoads[0] = null;
+        var drv = NewDriver(client);
+        await drv.InitializeAsync("{}", CancellationToken.None);
+
+        var load = await ReadSettledAsync(drv, $"{Host}/Spindle/S1/Load", s => s.StatusCode == FocasStatusMapper.BadNoData);
+
+        load.StatusCode.ShouldBe(FocasStatusMapper.BadNoData);
+        load.Value.ShouldBeNull();
+        await drv.ShutdownAsync(CancellationToken.None);
+    }
+
+    [Fact]
+    public async Task The_spindle_folder_offers_MotorSpeedPct_not_MaxRpm()
+    {
+        var drv = NewDriver(MachineClient());
+        await drv.InitializeAsync("{}", CancellationToken.None);
+        await ReadSettledAsync(drv, $"{Host}/Spindle/S1/Load", s => s.StatusCode == FocasStatusMapper.Good);
+
+        var builder = new NameRecordingBuilder();
+        await drv.DiscoverAsync(builder, CancellationToken.None);
+
+        builder.Variables.ShouldContain("MotorSpeedPct");
+        builder.Variables.ShouldNotContain("MaxRpm");
+        await drv.ShutdownAsync(CancellationToken.None);
+    }
+
+    private sealed class NameRecordingBuilder : IAddressSpaceBuilder
+    {
+        public List<string> Variables { get; } = [];
+        public IAddressSpaceBuilder Folder(string browseName, string displayName) => this;
+        public IVariableHandle Variable(string browseName, string displayName, DriverAttributeInfo attributeInfo)
+        {
+            Variables.Add(browseName);
+            return new Handle(attributeInfo.FullName);
+        }
+        public void AddProperty(string browseName, DriverDataType dataType, object? value) { }
+
+        private sealed class Handle(string fullRef) : IVariableHandle
+        {
+            public string FullReference => fullRef;
+            public IAlarmConditionSink MarkAsAlarmCondition(AlarmConditionInfo info) => throw new NotSupportedException();
+        }
+    }
+}
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasNameRecordTests.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasNameRecordTests.cs
new file mode 100644
index 00000000..9e0a6be1
--- /dev/null
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasNameRecordTests.cs
@@ -0,0 +1,78 @@
+using Shouldly;
+using Xunit;
+using ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Wire;
+
+namespace ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests;
+
+/// <summary>
+///     Axis-name (0x0089) / spindle-name (0x008A) record decode. Each record is 4 bytes; the name is
+///     the ASCII up to the record's FIRST NUL. Ported from the sister ignitionoee FOCAS driver
+///     (Focas.Wire-001 and Focas.Wire-022, v0.18.1).
+/// </summary>
+/// <remarks>
+///     <para><b>Reading only 2 bytes collides real names.</b> The live 31i-B capture
+///     (<c>ref-axisname-0x0089.bin</c>) carries <c>"AA6"</c> and <c>"AA7"</c>; the old 2-byte read
+///     turned both into <c>"AA"</c>, which is exactly the "one observed Makino returns two axis
+///     folders both called AA" that Gitea #548 then had to disambiguate as <c>AA_1</c>/<c>AA_2</c>.</para>
+///     <para><b>Trailing-only trimming keeps buffer residue.</b> A control writes only the bytes the
+///     name needs; on Makino Z-34184 (2026-08-19) <c>cnc_rdspdlname</c> came back
+///     <c>53 31 00 4e</c> — <c>"S1"</c> then the <c>'N'</c> of an earlier <c>"CNC"</c>. The name
+///     ends at the first NUL.</para>
+/// </remarks>
+[Trait("Category", "Unit")]
+public sealed class FocasNameRecordTests
+{
+    [Fact]
+    public void The_live_axis_name_capture_keeps_three_character_names_distinct()
+    {
+        var payload = WireFixtures.Payload("ref-axisname-0x0089.bin", 0x0089);
+
+        var names = FocasWireClient.ReadNameRecords(payload, 32, (index, name) => (index, name));
+
+        names.Select(n => n.name).ShouldBe(["X", "Y", "Z", "B", "C", "AA6", "AA7"]);
+        names.Select(n => n.index).ShouldBe([(short)1, 2, 3, 4, 5, 6, 7]);
+    }
+
+    [Fact]
+    public void The_live_spindle_name_capture_decodes()
+    {
+        var payload = WireFixtures.Payload("ref-spdlname-0x008a.bin", 0x008a);
+
+        FocasWireClient.ReadNameRecords(payload, 8, (_, name) => name).ShouldBe(["S1"]);
+    }
+
+    [Fact]
+    public void A_name_ends_at_its_first_NUL_so_residue_after_it_is_discarded()
+    {
+        // The Z-34184 spindle-name record: "S1", NUL, then an 'N' left over from a previous "CNC".
+        FocasWireProtocol.ReadNameRecord([0x53, 0x31, 0x00, 0x4e]).ShouldBe("S1");
+        // A single-character name with residue in BOTH trailing bytes.
+        FocasWireProtocol.ReadNameRecord([0x58, 0x00, 0x43, 0x4e]).ShouldBe("X");
+    }
+
+    [Fact]
+    public void All_four_record_bytes_are_name_bytes()
+    {
+        FocasWireProtocol.ReadNameRecord("AA6\0"u8.ToArray()).ShouldBe("AA6");
+        FocasWireProtocol.ReadNameRecord("ABCD"u8.ToArray()).ShouldBe("ABCD");
+        FocasWireProtocol.ReadNameRecord("X \0\0"u8.ToArray()).ShouldBe("X");
+    }
+
+    [Fact]
+    public void A_record_that_starts_with_NUL_is_blank()
+    {
+        FocasWireProtocol.ReadNameRecord([0x00, 0x41, 0x41, 0x00]).ShouldBe(string.Empty);
+    }
+
+    [Fact]
+    public void Servo_meter_names_come_out_whole_too()
+    {
+        var blocks = WireFixtures.Blocks("svmeter-pair-0x0056-0x0089.bin");
+        var sv = blocks.First(b => b.Command == 0x0056).Payload;
+        var names = blocks.First(b => b.Command == 0x0089).Payload;
+
+        var meters = FocasWireClient.ParseServoMeters(sv, names, maxCount: 32);
+
+        meters.Take(7).Select(m => m.Name).ShouldBe(["X", "Y", "Z", "B", "C", "AA6", "AA7"]);
+    }
+}
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasPositionAutoScaleTests.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasPositionAutoScaleTests.cs
deleted file mode 100644
index 9c698a6b..00000000
--- a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasPositionAutoScaleTests.cs
+++ /dev/null
@@ -1,164 +0,0 @@
-using Shouldly;
-using Xunit;
-using ZB.MOM.WW.OtOpcUa.Driver.FOCAS;
-
-namespace ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests;
-
-/// <summary>
-///     Phase 4b — per-axis auto-scale from <c>cnc_getfigure</c> figures. The driver fetches
-///     per-axis position decimal-place figures at init and applies them at the
-///     <see cref="FocasDriver"/> publish seam. Precedence: an auto figure for an axis WINS;
-///     the configured <c>PositionDecimalPlaces</c> is the per-axis fallback when the CNC did
-///     not report a figure for that axis. These tests drive the Fake to exercise the driver's
-///     auto-scale-vs-fallback logic independently of the wire path.
-/// </summary>
-[Trait("Category", "Unit")]
-public sealed class FocasPositionAutoScaleTests
-{
-    private const string Host = "focas://10.0.0.5:8193";
-
-    // A single-axis CNC (X only) so the snapshot we seed is unambiguous.
-    private static FakeFocasClient SingleAxisClient(
-        FocasDynamicSnapshot snap, IReadOnlyList<int> figures)
-    {
-        var c = new FakeFocasClient();
-        c.AxisNames.Clear();
-        c.AxisNames.Add(new("X", ""));
-        c.DynamicByAxis[1] = snap; // FOCAS axis indexing is 1-based
-        c.PositionFigures = figures;
-        return c;
-    }
-
-    // A two-axis CNC (X, Y) — each axis gets its own seeded snapshot + figure.
-    private static FakeFocasClient TwoAxisClient(
-        FocasDynamicSnapshot xSnap, FocasDynamicSnapshot ySnap, IReadOnlyList<int> figures)
-    {
-        var c = new FakeFocasClient();
-        c.AxisNames.Clear();
-        c.AxisNames.Add(new("X", ""));
-        c.AxisNames.Add(new("Y", ""));
-        c.DynamicByAxis[1] = xSnap; // axis 0 → 1-based index 1
-        c.DynamicByAxis[2] = ySnap; // axis 1 → 1-based index 2
-        c.PositionFigures = figures;
-        return c;
-    }
-
-    private static FocasDynamicSnapshot AbsSnap(int axisIndex, int absolutePosition) =>
-        new(AxisIndex: axisIndex, AlarmFlags: 0, ProgramNumber: 0, MainProgramNumber: 0,
-            SequenceNumber: 0, ActualFeedRate: 0, ActualSpindleSpeed: 0,
-            AbsolutePosition: absolutePosition, MachinePosition: 0,
-            RelativePosition: 0, DistanceToGo: 0);
-
-    private static FocasDriver NewDriver(int positionDecimalPlaces, FakeFocasClientFactory factory)
-    {
-        return new FocasDriver(new FocasDriverOptions
-        {
-            Devices = [new FocasDeviceOptions(Host, PositionDecimalPlaces: positionDecimalPlaces)],
-            Probe = new FocasProbeOptions { Enabled = false },
-            FixedTree = new FocasFixedTreeOptions
-            {
-                Enabled = true,
-                PollInterval = TimeSpan.FromMilliseconds(10),
-            },
-        }, "drv-1", factory);
-    }
-
-    // Drive the fixed-tree poll loop and wait (bounded) for the cached value to appear.
-    private static async Task<object?> ReadWhenPublishedAsync(FocasDriver drv, string reference)
-    {
-        var deadline = DateTime.UtcNow + TimeSpan.FromSeconds(5);
-        while (DateTime.UtcNow < deadline)
-        {
-            var snaps = await drv.ReadAsync([reference], CancellationToken.None);
-            var snap = snaps.Single();
-            if (snap.StatusCode == FocasStatusMapper.Good && snap.Value is not null)
-                return snap.Value;
-            await Task.Delay(15);
-        }
-        return null;
-    }
-
-    /// <summary>
-    ///     An auto figure for an axis WINS over the configured manual value: figure 3 ⇒ ÷10^3
-    ///     (12345 → 12.345), even though <c>PositionDecimalPlaces: 1</c> would have given ÷10.
-    /// </summary>
-    [Fact]
-    public async Task Auto_figure_wins_over_manual_config()
-    {
-        var factory = new FakeFocasClientFactory
-        {
-            Customise = () => SingleAxisClient(AbsSnap(1, 12345), figures: [3]),
-        };
-        var drv = NewDriver(positionDecimalPlaces: 1, factory);
-        await drv.InitializeAsync("{}", CancellationToken.None);
-
-        var abs = await ReadWhenPublishedAsync(drv, $"{Host}/Axes/X/AbsolutePosition");
-        abs.ShouldBe(12.345); // ÷10^3 (auto), NOT 1234.5 (manual ÷10)
-
-        await drv.ShutdownAsync(CancellationToken.None);
-    }
-
-    /// <summary>
-    ///     When <c>cnc_getfigure</c> reports nothing (empty list — the real wire backend's
-    ///     behaviour), the driver falls back to the configured <c>PositionDecimalPlaces</c>:
-    ///     manual 2 ⇒ ÷10^2 (12345 → 123.45).
-    /// </summary>
-    [Fact]
-    public async Task Falls_back_to_manual_when_getfigure_empty()
-    {
-        var factory = new FakeFocasClientFactory
-        {
-            Customise = () => SingleAxisClient(AbsSnap(1, 12345), figures: []),
-        };
-        var drv = NewDriver(positionDecimalPlaces: 2, factory);
-        await drv.InitializeAsync("{}", CancellationToken.None);
-
-        var abs = await ReadWhenPublishedAsync(drv, $"{Host}/Axes/X/AbsolutePosition");
-        abs.ShouldBe(123.45); // ÷10^2 (manual fallback)
-
-        await drv.ShutdownAsync(CancellationToken.None);
-    }
-
-    /// <summary>
-    ///     Figures are applied per-axis independently: figures [3, 1] ⇒ axis 0 ÷10^3 and
-    ///     axis 1 ÷10^1.
-    /// </summary>
-    [Fact]
-    public async Task Per_axis_figures_scale_independently()
-    {
-        var factory = new FakeFocasClientFactory
-        {
-            Customise = () => TwoAxisClient(
-                AbsSnap(1, 12345), AbsSnap(2, 67890), figures: [3, 1]),
-        };
-        var drv = NewDriver(positionDecimalPlaces: 0, factory);
-        await drv.InitializeAsync("{}", CancellationToken.None);
-
-        var x = await ReadWhenPublishedAsync(drv, $"{Host}/Axes/X/AbsolutePosition");
-        var y = await ReadWhenPublishedAsync(drv, $"{Host}/Axes/Y/AbsolutePosition");
-        x.ShouldBe(12.345);  // ÷10^3
-        y.ShouldBe(6789.0);  // ÷10^1
-
-        await drv.ShutdownAsync(CancellationToken.None);
-    }
-
-    /// <summary>
-    ///     The legacy manual-only path is unchanged: no auto figures + <c>PositionDecimalPlaces: 0</c>
-    ///     ⇒ factor 1.0, so the raw integer is published widened to double (12345 → 12345.0).
-    /// </summary>
-    [Fact]
-    public async Task Manual_only_legacy_path_unchanged()
-    {
-        var factory = new FakeFocasClientFactory
-        {
-            Customise = () => SingleAxisClient(AbsSnap(1, 12345), figures: []),
-        };
-        var drv = NewDriver(positionDecimalPlaces: 0, factory);
-        await drv.InitializeAsync("{}", CancellationToken.None);
-
-        var abs = await ReadWhenPublishedAsync(drv, $"{Host}/Axes/X/AbsolutePosition");
-        abs.ShouldBe(12345.0); // factor 1.0 — raw widened to double
-
-        await drv.ShutdownAsync(CancellationToken.None);
-    }
-}
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasPositionBlockScaleTests.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasPositionBlockScaleTests.cs
new file mode 100644
index 00000000..26f5e001
--- /dev/null
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasPositionBlockScaleTests.cs
@@ -0,0 +1,105 @@
+using Shouldly;
+using Xunit;
+using ZB.MOM.WW.OtOpcUa.Core.Abstractions;
+using ZB.MOM.WW.OtOpcUa.Driver.FOCAS;
+
+namespace ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests;
+
+/// <summary>
+///     Driver-level publish of self-describing <c>cnc_rddynamic2</c> positions. Each block's own
+///     <c>base^exponent</c> wins over the configured <c>PositionDecimalPlaces</c> (which is now only
+///     the fallback for a scale-less block), and a block describing no usable position Bads its own
+///     node without disturbing its siblings. Replaces the <c>cnc_getfigure</c> (0x00D3) auto-scale
+///     tests — that command is not a FOCAS wire command; the real 31i-B refuses it with <c>rc=1</c>.
+/// </summary>
+[Trait("Category", "Unit")]
+public sealed class FocasPositionBlockScaleTests
+{
+    private const string Host = "focas://10.0.0.5:8193";
+
+    private static FocasDynamicSnapshot Snap(int axisIndex, FocasPosition abs, FocasPosition mach) =>
+        new(AxisIndex: axisIndex, AlarmFlags: 0, ProgramNumber: 0, MainProgramNumber: 0,
+            SequenceNumber: 0, ActualFeedRate: 0, ActualSpindleSpeed: 0,
+            AbsolutePosition: abs, MachinePosition: mach, RelativePosition: 0, DistanceToGo: 0);
+
+    private static FocasDriver NewDriver(int positionDecimalPlaces, FakeFocasClient client) =>
+        new(new FocasDriverOptions
+        {
+            Devices = [new FocasDeviceOptions(Host, PositionDecimalPlaces: positionDecimalPlaces)],
+            Probe = new FocasProbeOptions { Enabled = false },
+            FixedTree = new FocasFixedTreeOptions { Enabled = true, PollInterval = TimeSpan.FromMilliseconds(10) },
+        }, "drv-1", new FakeFocasClientFactory { Customise = () => client });
+
+    private static async Task<DataValueSnapshot> ReadWhenPolledAsync(FocasDriver drv, string reference)
+    {
+        var deadline = DateTime.UtcNow + TimeSpan.FromSeconds(5);
+        DataValueSnapshot last;
+        do
+        {
+            // Until the first poll lands the reference resolves to nothing; once it has, the node
+            // reads either Good or (for an undescribable block) BadNoData.
+            last = (await drv.ReadAsync([reference], CancellationToken.None)).Single();
+            if (last.StatusCode is FocasStatusMapper.Good or FocasStatusMapper.BadNoData) return last;
+            await Task.Delay(15);
+        } while (DateTime.UtcNow < deadline);
+        return last;
+    }
+
+    private static FakeFocasClient XAxisClient(FocasDynamicSnapshot snap)
+    {
+        var c = new FakeFocasClient();
+        c.AxisNames.Clear();
+        c.AxisNames.Add(new("X", ""));
+        c.DynamicByAxis[1] = snap;
+        return c;
+    }
+
+    [Fact]
+    public async Task The_blocks_own_scale_wins_over_PositionDecimalPlaces()
+    {
+        // The live 31i-B shape: raw 2801574, base 10, exponent 4 → 280.1574 mm.
+        var client = XAxisClient(Snap(1, new FocasPosition(2_801_574, 10, 4, HasScale: true), 0));
+        var drv = NewDriver(positionDecimalPlaces: 1, client);
+        await drv.InitializeAsync("{}", CancellationToken.None);
+
+        var abs = await ReadWhenPolledAsync(drv, $"{Host}/Axes/X/AbsolutePosition");
+
+        abs.StatusCode.ShouldBe(FocasStatusMapper.Good);
+        ((double)abs.Value!).ShouldBe(280.1574, 1e-9); // NOT 280157.4 (the ÷10 fallback)
+        await drv.ShutdownAsync(CancellationToken.None);
+    }
+
+    [Fact]
+    public async Task A_scale_less_block_falls_back_to_PositionDecimalPlaces()
+    {
+        var client = XAxisClient(Snap(1, 12345, 0));
+        var drv = NewDriver(positionDecimalPlaces: 2, client);
+        await drv.InitializeAsync("{}", CancellationToken.None);
+
+        var abs = await ReadWhenPolledAsync(drv, $"{Host}/Axes/X/AbsolutePosition");
+
+        abs.StatusCode.ShouldBe(FocasStatusMapper.Good);
+        abs.Value.ShouldBe(123.45);
+        await drv.ShutdownAsync(CancellationToken.None);
+    }
+
+    [Fact]
+    public async Task A_vacant_block_bads_its_own_node_and_not_its_sibling()
+    {
+        var client = XAxisClient(Snap(
+            1,
+            abs: new FocasPosition(0, 10, 0xFFFF, HasScale: true),   // vacant-slot marker
+            mach: new FocasPosition(-22000, 10, 3, HasScale: true)));
+        var drv = NewDriver(positionDecimalPlaces: 0, client);
+        await drv.InitializeAsync("{}", CancellationToken.None);
+
+        var mach = await ReadWhenPolledAsync(drv, $"{Host}/Axes/X/MachinePosition");
+        var abs = await ReadWhenPolledAsync(drv, $"{Host}/Axes/X/AbsolutePosition");
+
+        mach.StatusCode.ShouldBe(FocasStatusMapper.Good);
+        mach.Value.ShouldBe(-22.0);
+        abs.StatusCode.ShouldBe(FocasStatusMapper.BadNoData);
+        abs.Value.ShouldBeNull("an undescribable block is not a Good 0.0 at the origin");
+        await drv.ShutdownAsync(CancellationToken.None);
+    }
+}
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasPositionDecodeTests.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasPositionDecodeTests.cs
new file mode 100644
index 00000000..e515e3d5
--- /dev/null
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasPositionDecodeTests.cs
@@ -0,0 +1,107 @@
+using System.Buffers.Binary;
+using Shouldly;
+using Xunit;
+using ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Wire;
+
+namespace ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests;
+
+/// <summary>
+///     <c>cnc_rddynamic2</c> position blocks (0x0026) are self-describing: <c>[0..3] i32 raw</c>,
+///     <c>[4..5] u16 base</c> (2 or 10), <c>[6..7] u16 exponent</c> (<c>0xFFFF</c> = vacant slot);
+///     <c>value = raw / base^exponent</c>. Ported from the sister ignitionoee FOCAS driver v0.17.0
+///     (which also deleted the fabricated <c>cnc_getfigure</c> 0x00D3 — the real 31i-B refuses it
+///     with <c>rc=1</c>) and Focas.Wire-014 (absurd exponents are refused, not divided by).
+/// </summary>
+[Trait("Category", "Unit")]
+public sealed class FocasPositionDecodeTests
+{
+    private static byte[] Block(int raw, int @base, int exponent)
+    {
+        var b = new byte[8];
+        BinaryPrimitives.WriteInt32BigEndian(b.AsSpan(0, 4), raw);
+        BinaryPrimitives.WriteUInt16BigEndian(b.AsSpan(4, 2), (ushort)@base);
+        BinaryPrimitives.WriteUInt16BigEndian(b.AsSpan(6, 2), (ushort)exponent);
+        return b;
+    }
+
+    [Fact]
+    public void The_live_dynamic2_capture_scales_every_position_from_its_own_block()
+    {
+        // ref-dynamic2-axis1.bin: four 0x0026 blocks (absolute / machine / relative / distance of
+        // axis 1), every one base 10, exponent 4. Undecoded they read 2801574 / 2801200 / 32 / 0.
+        var dynamic = FocasWireClient.ParseDynamic2(WireFixtures.Blocks("ref-dynamic2-axis1.bin"));
+
+        dynamic.Axis.Absolute.ToEngineering(0)!.Value.ShouldBe(280.1574, 1e-9);
+        dynamic.Axis.Machine.ToEngineering(0)!.Value.ShouldBe(280.1200, 1e-9);
+        dynamic.Axis.Relative.ToEngineering(0)!.Value.ShouldBe(0.0032, 1e-9);
+        dynamic.Axis.Distance.ToEngineering(0)!.Value.ShouldBe(0.0, 1e-9);
+        dynamic.FeedRate.ShouldBe(0);
+        dynamic.SpindleSpeed.ShouldBe(0);
+    }
+
+    [Fact]
+    public void The_block_scale_wins_over_the_configured_decimal_places()
+    {
+        var p = FocasWireClient.ParsePositionBlock(Block(123456, 10, 3));
+        p.ToEngineering(fallbackDecimalPlaces: 1)!.Value.ShouldBe(123.456, 1e-9);
+    }
+
+    [Theory]
+    [InlineData("live-dynamic2-axis1-0x0026.bin", 0.0374)]   // Z-34184 X
+    [InlineData("live-dynamic2-axis2-0x0026.bin", 370.177)]  // Z-34184 Y
+    public void Axis_scoped_live_requests_return_that_axis_scaled(string fixture, double expected)
+    {
+        var blocks = WireFixtures.Blocks(fixture).Where(b => b.Command == 0x0026).ToList();
+        blocks.Count.ShouldBe(1, "an axis-scoped request returns exactly one 0x0026 block");
+
+        FocasWireClient.ParsePositionBlock(blocks[0].Payload).ToEngineering(0)!.Value.ShouldBe(expected, 1e-9);
+    }
+
+    [Theory]
+    [InlineData(40, 2, 3, 5.0)]           // inch-mode binary base
+    [InlineData(-22000, 10, 3, -22.0)]
+    [InlineData(42, 10, 0, 42.0)]
+    public void Positions_scale_by_base_to_the_exponent(int raw, int @base, int exponent, double expected)
+    {
+        FocasWireClient.ParsePositionBlock(Block(raw, @base, exponent)).ToEngineering(0)!.Value.ShouldBe(expected, 1e-9);
+    }
+
+    [Theory]
+    [InlineData(1, 10, 0xFFFF)]   // vacant-slot marker
+    [InlineData(1234, 7, 2)]      // base neither 2 nor 10
+    [InlineData(1234, 0, 2)]
+    [InlineData(123456, 10, 400)] // would divide by Infinity → a Good 0.0 at the origin
+    [InlineData(123456, 10, 40)]
+    public void An_undescribable_block_has_no_value(int raw, int @base, int exponent)
+    {
+        var p = FocasWireClient.ParsePositionBlock(Block(raw, @base, exponent));
+        p.IsValid.ShouldBeFalse();
+        p.ToEngineering(3).ShouldBeNull();
+    }
+
+    [Fact]
+    public void Every_plausible_exponent_still_decodes()
+    {
+        for (var exp = 0; exp <= 18; exp++)
+            FocasWireClient.ParsePositionBlock(Block(1, 10, exp)).IsValid.ShouldBeTrue($"exponent {exp}");
+    }
+
+    [Fact]
+    public void A_block_without_a_scale_falls_back_to_the_configured_decimal_places()
+    {
+        // A 4-byte block carries no envelope (older simulators); only then does
+        // PositionDecimalPlaces apply.
+        var p = FocasWireClient.ParsePositionBlock([0x00, 0x00, 0x30, 0x39]); // 12345
+        p.HasScale.ShouldBeFalse();
+        p.ToEngineering(2)!.Value.ShouldBe(123.45, 1e-9);
+        p.ToEngineering(0)!.Value.ShouldBe(12345.0);
+    }
+
+    [Fact]
+    public void A_raw_integer_position_converts_implicitly_as_a_scale_less_value()
+    {
+        FocasPosition p = 12345;
+        p.HasScale.ShouldBeFalse();
+        p.Raw.ShouldBe(12345);
+    }
+}
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasPositionScalingTests.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasPositionScalingTests.cs
index 860de0dc..af5b0f29 100644
--- a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasPositionScalingTests.cs
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasPositionScalingTests.cs
@@ -5,12 +5,11 @@ using ZB.MOM.WW.OtOpcUa.Driver.FOCAS;
 namespace ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests;
 
 /// <summary>
-///     Phase 4 data-type tier — axis-position scaling. <c>cnc_rddynamic2</c> returns
-///     positions as scaled integers; the driver applies a <c>10^PositionDecimalPlaces</c>
-///     divide at the <see cref="FocasDriver"/> publish seam so positions surface in
-///     engineering units on the Float64 axis nodes. The managed wire backend fetches per-axis
-///     figures live via <c>cnc_getfigure</c>; the config knob is the per-axis fallback used
-///     when the CNC reports no figure for an axis. These tests cover the config-supplied path.
+///     Phase 4 data-type tier — axis-position scaling, config-supplied fallback path. A real
+///     CNC's <c>cnc_rddynamic2</c> position block carries its own <c>base^exponent</c> scale
+///     (covered by <see cref="FocasPositionBlockScaleTests"/>); a scale-less position — the
+///     raw integers these tests seed — is divided by <c>10^PositionDecimalPlaces</c> at the
+///     <see cref="FocasDriver"/> publish seam.
 /// </summary>
 [Trait("Category", "Unit")]
 public sealed class FocasPositionScalingTests
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasProgramInfoQualityTests.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasProgramInfoQualityTests.cs
new file mode 100644
index 00000000..ad2479b1
--- /dev/null
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasProgramInfoQualityTests.cs
@@ -0,0 +1,92 @@
+using Shouldly;
+using Xunit;
+using ZB.MOM.WW.OtOpcUa.Driver.FOCAS;
+using ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Wire;
+
+namespace ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests;
+
+/// <summary>
+///     "The control did not say" must read Bad, never a fabricated Good 0. Ported from the sister
+///     ignitionoee FOCAS driver (commit 101a3b1, 2026-08-12): a <c>cnc_exeprgname2</c> payload too
+///     short to carry the O-number published <c>0</c> at Good quality — indistinguishable from a
+///     31i's genuine 0 for a path-executed program. The same idiom covered every sub-read of the
+///     program bundle here: a refused <c>cnc_rdopmode</c> published Mode <c>0</c> (= MDI, a real
+///     mode) and a refused <c>cnc_rdblkcount</c> a BlockCount of 0.
+/// </summary>
+[Trait("Category", "Unit")]
+public sealed class FocasProgramInfoQualityTests
+{
+    private const string Host = "focas://10.0.0.5:8193";
+
+    private static FocasResult<WireProgramName> Name(string name, int? oNumber) => new(0, new WireProgramName(name, oNumber));
+
+    [Fact]
+    public void A_payload_without_an_O_number_maps_to_null_not_zero()
+    {
+        var info = WireFocasClient.MapProgramInfo(Name("O1111", null), new(0, 42), new(0, 1));
+
+        info.Name.ShouldBe("O1111");
+        info.ONumber.ShouldBeNull();
+        info.BlockCount.ShouldBe(42);
+        info.Mode.ShouldBe(1);
+    }
+
+    [Fact]
+    public void A_genuine_zero_O_number_stays_zero()
+    {
+        // Live Z-34184: a 256-byte payload whose o_num is present and genuinely 0.
+        WireFocasClient.MapProgramInfo(Name("//CNC_MEM/USER/LIBRARY/O1111", 0), new(0, 0), new(0, 1))
+            .ONumber.ShouldBe(0);
+    }
+
+    [Fact]
+    public void Refused_sub_reads_map_to_null_not_a_fabricated_value()
+    {
+        var info = WireFocasClient.MapProgramInfo(Name("O1", 1), new FocasResult<int>(1, 0), new FocasResult<short>(1, 0));
+
+        info.BlockCount.ShouldBeNull();
+        info.Mode.ShouldBeNull("Mode 0 is MDI — a real mode, not 'unknown'");
+
+        var nameless = WireFocasClient.MapProgramInfo(new FocasResult<WireProgramName>(1, null), new(0, 3), new(0, 1));
+        nameless.Name.ShouldBeNull();
+        nameless.ONumber.ShouldBeNull();
+    }
+
+    [Fact]
+    public async Task A_missing_field_reads_BadNoData_while_its_siblings_stay_good()
+    {
+        var client = new FakeFocasClient { ProgramInfo = new FocasProgramInfo("O1111", null, 12, null) };
+        var drv = new FocasDriver(new FocasDriverOptions
+        {
+            Devices = [new FocasDeviceOptions(Host)],
+            Probe = new FocasProbeOptions { Enabled = false },
+            FixedTree = new FocasFixedTreeOptions
+            {
+                Enabled = true,
+                PollInterval = TimeSpan.FromMilliseconds(10),
+                ProgramPollInterval = TimeSpan.FromMilliseconds(10),
+            },
+        }, "drv-1", new FakeFocasClientFactory { Customise = () => client });
+        await drv.InitializeAsync("{}", CancellationToken.None);
+
+        var deadline = DateTime.UtcNow + TimeSpan.FromSeconds(5);
+        while (DateTime.UtcNow < deadline && drv.GetDeviceState(Host)?.LastProgramInfo is null)
+            await Task.Delay(15);
+
+        var read = await drv.ReadAsync(
+            [$"{Host}/Program/Name", $"{Host}/Program/BlockCount", $"{Host}/Program/ONumber",
+             $"{Host}/OperationMode/Mode", $"{Host}/OperationMode/ModeText"],
+            CancellationToken.None);
+
+        read[0].StatusCode.ShouldBe(FocasStatusMapper.Good);
+        read[0].Value.ShouldBe("O1111");
+        read[1].StatusCode.ShouldBe(FocasStatusMapper.Good);
+        read[1].Value.ShouldBe(12);
+        read[2].StatusCode.ShouldBe(FocasStatusMapper.BadNoData);
+        read[2].Value.ShouldBeNull();
+        read[3].StatusCode.ShouldBe(FocasStatusMapper.BadNoData);
+        read[4].StatusCode.ShouldBe(FocasStatusMapper.BadNoData);
+
+        await drv.ShutdownAsync(CancellationToken.None);
+    }
+}
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasWireProtocolTests.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasWireProtocolTests.cs
index ad6bb6fd..eb501502 100644
--- a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasWireProtocolTests.cs
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasWireProtocolTests.cs
@@ -10,7 +10,7 @@ namespace ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests;
 ///     Offline byte-level coverage for the managed FOCAS/2 wire-protocol decode layer
 ///     (<see cref="FocasWireProtocol"/>) — the big-endian framing + block-envelope decode that
 ///     is this driver's analogue of P/Invoke struct marshalling. Before this suite the entire
-///     wire decode surface (including the <c>cnc_getfigure</c> figure stride) ran without a
+///     wire decode surface ran without a
 ///     single byte-level test; every other test drives the <c>IFocasClient</c> seam through the
 ///     Fake, which bypasses all framing. Recorded as Driver.FOCAS-013.
 /// </summary>
@@ -200,29 +200,6 @@ public sealed class FocasWireProtocolTests
         Should.Throw<FocasWireException>(() => FocasWireProtocol.ParseResponseBlocks(body));
     }
 
-    // ---- The cnc_getfigure figure stride: decode a response block into shorts ----
-
-    [Fact]
-    public void ParseResponseBlocks_yields_a_payload_that_decodes_as_a_sequence_of_figure_shorts()
-    {
-        // cnc_getfigure (command 0x00d3) returns one big-endian short per axis. Build the
-        // response block and assert the payload decodes to the [3, 1, 0] figure sequence the
-        // driver's auto-scale path reads.
-        var figurePayload = new byte[6];
-        BinaryPrimitives.WriteInt16BigEndian(figurePayload.AsSpan(0, 2), 3);
-        BinaryPrimitives.WriteInt16BigEndian(figurePayload.AsSpan(2, 2), 1);
-        BinaryPrimitives.WriteInt16BigEndian(figurePayload.AsSpan(4, 2), 0);
-
-        var body = BuildResponseBody((command: (ushort)0x00d3, rc: (short)0, payload: figurePayload));
-        var block = FocasWireProtocol.ParseResponseBlocks(body).Single();
-
-        var figures = new List<int>();
-        for (var offset = 0; offset + 2 <= block.Payload.Length; offset += 2)
-            figures.Add(BinaryPrimitives.ReadInt16BigEndian(block.Payload.AsSpan(offset, 2)));
-
-        figures.ShouldBe(new[] { 3, 1, 0 });
-    }
-
     // ---- ReadAscii / ReadNameRecord ----
 
     [Fact]
@@ -239,11 +216,12 @@ public sealed class FocasWireProtocolTests
     }
 
     [Fact]
-    public void ReadNameRecord_reads_two_bytes_and_strips_padding()
+    public void ReadNameRecord_strips_padding()
     {
+        // Full record semantics (first NUL, all four bytes) are pinned in FocasNameRecordTests.
         FocasWireProtocol.ReadNameRecord("X \0\0"u8.ToArray()).ShouldBe("X");
         FocasWireProtocol.ReadNameRecord("XY"u8.ToArray()).ShouldBe("XY");
-        FocasWireProtocol.ReadNameRecord(new byte[] { 0x58 }).ShouldBe(string.Empty); // < 2 bytes
+        FocasWireProtocol.ReadNameRecord(ReadOnlySpan<byte>.Empty).ShouldBe(string.Empty);
     }
 
     // ---- helpers ----
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasWireV3Tests.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasWireV3Tests.cs
index d3866896..c0b6c638 100644
--- a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasWireV3Tests.cs
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/FocasWireV3Tests.cs
@@ -98,7 +98,7 @@ public sealed class FocasWireV3Tests
     [Fact]
     public void ParseServoMeters_uses_an_eight_byte_stride_and_names_from_the_axis_block()
     {
-        // Three 8-byte records {int32 data; int16 dec=10; int16 unit=0}: data = 0, 50, -3.
+        // Three 8-byte records {int32 value; u16 base=10; u16 exponent=0}: value = 0, 50, -3.
         byte[] sv =
         [
             0x00, 0x00, 0x00, 0x00, 0x00, 0x0a, 0x00, 0x00, // axis 1: data=0
@@ -120,7 +120,8 @@ public sealed class FocasWireV3Tests
         meters[0].Value.ShouldBe(0);
         meters[1].Name.ShouldBe("Y");
         meters[1].Value.ShouldBe(50);   // 8-byte stride: a 12-byte stride would misread this as 655360
-        meters[1].Decimal.ShouldBe((short)10);
+        meters[1].Base.ShouldBe(10);       // offset 4 is the envelope BASE, not a decimal count
+        meters[1].Scaled.ShouldBe(50.0);
         meters[2].Name.ShouldBe("Z");
         meters[2].Value.ShouldBe(-3);
     }
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/WireFixtures.cs b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/WireFixtures.cs
new file mode 100644
index 00000000..0960bd37
--- /dev/null
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/WireFixtures.cs
@@ -0,0 +1,31 @@
+using ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Wire;
+
+namespace ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests;
+
+/// <summary>
+///     Loads the raw FOCAS response PDUs under <c>Fixtures/v3/</c> — byte-for-byte captures from a
+///     real FANUC 31i-B (Makino, series G431) — and splits them into response blocks with the
+///     production <see cref="FocasWireProtocol.ParseResponseBlocks"/>. The <c>live-*</c> captures
+///     were taken by the sister ignitionoee FOCAS driver's read-only probes of Z-34184 (2026-08-12)
+///     and are shared verbatim; the <c>ref-*</c> ones are this repo's own 2026-06-25 capture.
+/// </summary>
+internal static class WireFixtures
+{
+    private const int PduHeaderLength = 10;
+
+    /// <summary>Every response block of the named capture, in wire order.</summary>
+    /// <param name="name">File name under <c>Fixtures/v3/</c>.</param>
+    /// <returns>The parsed response blocks.</returns>
+    public static IReadOnlyList<ResponseBlock> Blocks(string name)
+    {
+        var raw = File.ReadAllBytes(Path.Combine(AppContext.BaseDirectory, "Fixtures", "v3", name));
+        return FocasWireProtocol.ParseResponseBlocks(raw.AsSpan(PduHeaderLength));
+    }
+
+    /// <summary>The payload of the first block carrying <paramref name="command"/>.</summary>
+    /// <param name="name">File name under <c>Fixtures/v3/</c>.</param>
+    /// <param name="command">The FOCAS command id to locate.</param>
+    /// <returns>That block's payload bytes.</returns>
+    public static byte[] Payload(string name, ushort command) =>
+        Blocks(name).First(b => b.Command == command).Payload;
+}
diff --git a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests.csproj b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests.csproj
index 5d596302..4a98f116 100644
--- a/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests.csproj
+++ b/tests/Drivers/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests/ZB.MOM.WW.OtOpcUa.Driver.FOCAS.Tests.csproj
@@ -19,6 +19,11 @@
         </PackageReference>
     </ItemGroup>
 
+    <ItemGroup>
+        <!-- Real FANUC 31i-B response captures (raw PDUs); read by WireFixtures. -->
+        <None Include="Fixtures\v3\*.bin" CopyToOutputDirectory="PreserveNewest"/>
+    </ItemGroup>
+
     <ItemGroup>
         <ProjectReference Include="..\..\..\src\Drivers\ZB.MOM.WW.OtOpcUa.Driver.FOCAS\ZB.MOM.WW.OtOpcUa.Driver.FOCAS.csproj"/>
     </ItemGroup>